WeatherTech BumpStep for 2 Inch Hitch Receiver

Question

Question:

Are you able to stock the WeatherTech BumpStop XL? Thanks

asked by: Joe F

0

Expert Reply:

We carry the WeatherTech BumpStep Hitch-Mounted Bumper Protector and Step for 2" Hitches # WT81BS1 and recently added the BumpStep XL # WT81BS1XL which has a 24 inch length versus the 12 inch length.

expert reply by: Jason S

0

Answer 1

I reached out to my contact at WeatherTech regarding backup sensor interference with the BumpStep Hitch-Mounted Bumper Protector and Step for 2" Hitches #WT81BS1, and he advised me of no known issues with this matter.

view full answer...

Answer 2

I recommend the Hopkins Mounting Bracket #HM48605 for securing the Pollak 5-Pole, Round Pin Trailer Wiring Socket #PK11502. The Hopkins bracket has a slit in the bottom which allows you to easily attach and remove the connector without having to…

view full answer...

Answer 3

I went out to the warehouse and pulled the Hopkins 4, 5, and 6-Way mounting bracket #HM48605 to measure it for you. The outer most holes are 2-7/8 inches apart on center. The inner set are 1-7/8 inches apart on center. The holes are just a hair over…

view full answer...

Answer 4

It sounds like you might be looking for a hitch mounted step. If that is the case we do have several options for this, like the WeatherTech BumpStepXL Hitch-Mounted Bumper Protector and Step part #WT81BS1XL you mentioned. I have attached a full list…

view full answer...

Answer 5

I wouldn't think so, but to be sure you can compare the measurements of the Weathertech part #WT81BS1 to the backup sensor locations. This is overall 11-1/2 inches wide and 2-1/2 inches tall. This should be small enough and also low enough not to…

view full answer...

Answer 6

Since you are looking for a step that can be used with your tailgate down, I recommend taking a look at the HitchMate Extendable TruckStep, #HE4045. This step was designed for that specific purpose and offers a support strut that extends step…

view full answer...

Answer 7

There are two front hitch options we have for your 2018 Ford F-250 which are very similar. We have the Draw Tite part #65076 and the Curt #C31078 which are both really great options. The big differences are that the Draw Tite will stick out past the…

view full answer...

Answer 8

I ran out to the warehouse and took some measurements of the Carr Hitch Mounted Step for 2" Trailer Hitches #CARR183252 and got the following measurements depicted below. Closed: Center of first hole: 3-3/8" Center of second hole:…

view full answer...

Answer 9

For the lift gate kick sensor with your 2021 Honda Pilot and the Curt Trailer Hitch Receiver #C13146, I have also read that some have not had to relocate the sensor with the Honda kit. But some have also expressed that the system works but not all of…

view full answer...

Answer 10

Thank you for the picture. Unfortunately, there isn't going to be a hitch for the 2017 Ram ProMaster 3500 that is compatible with that step. Even something like the Draw-Tite #75882 which hangs down a little bit further than the Curt #C13295 is…

view full answer...

Answer 11

I tested this lock, Anti-Rattle Trailer Hitch Receiver Lock for 2" Hitches - 3-1/2" Span, part #63232 will work with the Carr Flip Step, part #CARR190011B, and it works. I also tested it with the Curt Anti-Rattle Kit for Hollow Shank…

view full answer...

Answer 12

Yes, you can use the Anti-Rattle Trailer Hitch Receiver Lock for 2" Hitches - 3-1/2" Span, part #63232, with the Carr Mega Step Fold-Up Step - 2" Hitch - 14" Long - 500 lbs - Black, part #CARR190011B. I have included a product…

view full answer...

WeatherTech BumpStep for 2 Inch Hitch Receiver

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching