Mounting Instructions for the Tekonsha Primus IQ # TK90160 Electronic Brake Controller

Question

Question:

Can the Tekonsha 90160 Primus IQ Electronic Brake Control be mounted vertically with the screen up hooked on to my center council pocket? From what I am reading I would say not the correct way.

asked by: Joe

0

Expert Reply:

The Tekonsha Primus IQ # TK90160 can be mounted at a vertical angle between 0 and 90 degrees and it will still level itself out. You do need to ensure that it is level on the horizontal plane.

I have attached some photos as well as the installation details for you to check out.

expert reply by: Jon G

0

click to enlarge

Answer 1

According to my research, your 92865A-1 hub/drum has a 25580 inner and an 14125A outer bearing and a 8 on 6-1/2 inch lug pattern, as does the AxleTek #AKHD-865-7-2-K hub drum you referenced. The #AKHD-865-7-2-K would be an acceptable replacement…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

I know exactly what you need; I recommend using the Timbren Rear Suspension Enhancement System #TTORSEQ. The Timbren SES is designed to combat the sag you're experiencing and provide a more comfortable ride by absorbing road shock and…

view full answer...

Answer 4

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 9

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 10

Hey Donald, the best Blue Ox weight distribution would be the pat #BXW0550 as it has a perfect tongue weight range for your 450 lb tongue weight trailer.

view full answer...

Answer 11

For your 2024 Hyunda Santa Cruz we have the Curt 7-way kit part #C68JR that is a confirmed fit. This installs by plugging into a factory wiring connector on your vehicle which means a really easy install that doesn't require any splicing.

view full answer...

Answer 12

The correct Roadactive kit that fits your 2023 Ford F-150 is the part #RAS3611-YHD. I really like the RAS kits as they basically don't have any downsides. You get the adjustable support, an easy install, no maintenance, and actually…

view full answer...