Will Bulldog Powered Drive Trailer Jack BD500199 Replace Manual Jack w/Triangle Mounting Bracket

Question

Question:

I am purchasing a Keystone Passport TT that has a manual jack with a triangular-shaped mounting plate to the frame see photo. Will the circular mounting plate of this Bulldog jack fit where the triangular plate is now? I dont want to have to drill holes in the frame. Will the bolt holes in the circular plate line up with where the holes are now for the manual jack? Thank you!

asked by: David

0

Expert Reply:

Yes, you can use the Bulldog Powered Drive Trailer Jack # BD500199 in place of your existing jack because the mounting hole pattern in the bracket will be the same between the 2 jacks. Provided that your existing jack also has a round outer tube that is 2-1/4 inches in diameter you will be good to go.

expert reply by: Michael H

0

Answer 1

Technically, your A-Frame Bulldog Powered Jack, Item #BD500199, can be powered by the 12 volt circuit on a 7-Way trailer side connector which is in the 1 o'clock position where the wires connect if looking at the back of the 7-Way…

view full answer...

Answer 2

There is no reason why you could not turn the jack at a 90 degree angle to gain more clearance. Due to the configuration of the holes in the mounting flange, you might need to drill new holes in your trailer tongue to mount the jack in that…

view full answer...

Answer 3

There are some Dutton-Lainson trailer jacks that are made in the USA as well as a few that are not. Any jacks that we carry that are made in the USA have that as part of the description to help set them apart. Currently we have the following…

view full answer...

Answer 4

The Bulldog Powered Jack #BD500199 comes with everything you need. This includes installation hardware, hand crank, and a spring-loaded pull pin that quickly releases the drop leg into position.

view full answer...

Answer 5

I highly doubt that the jack itself is the issue. Typically when a trailer jack has trouble extending but not retracting that is due to a bad ground connection or a depleted battery, with the battery being the more common of the two. Gravity helps…

view full answer...

Answer 6

When an electric trailer tongue jack like the Barker VIP 3500 will not operate with electric power the two most common causes are a weak ground connection or a battery with an insufficient charge. I checked the online installation/operation…

view full answer...

Answer 7

What I would recommend is to use the bike rack bunk part #CC-275 which attaches to the A-frame of the trailer to give you a hitch opening above the frame so that a bike rack like the Swagman Trailhead #S63381 can be carried. I attached a review video…

view full answer...

Answer 8

The Atwood Power Trailer Jack with Cover and Foot has a lift speed of 15 inches per minute. It also has a lift range of 14 inches. This jack has been around for a very long time and is very dependable. The wiring on this jack is slightly larger than…

view full answer...

Answer 9

There is a Bulldog jack that has numerous bolt holes to allow you to unbolt the jack and rotate it 90 degrees, the Bulldog Powered Drive Trailer Jack #BD500199. You can see an example of this in the linked video - just forward to about the 6:15 mark.…

view full answer...

Answer 10

Replacement manual lift knob #FVK1142-09 is going to be the best option we have for your 4251 series vent. This is the new style that replaces the old 4-wing knob.

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Will Bulldog Powered Drive Trailer Jack BD500199 Replace Manual Jack w/Triangle Mounting Bracket

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching