Dimensions of TorkLift GlowStep Stow N' Go Mounting Bracket TLA7810

Question

Question:

In answer to another posters Teala question, the Expert answered that bracket TLA7810 is 23inch wide x 7.5inch tall. An accompanying diagram suggested that the inside portion of the bracket is 23. 1 Since the bracket appears to be made of 1/4inch steel...does that mean that the outside width is 23.5, which is the minimum available space widthwise needed to mount the bracket? 2 Would you also confirm that the inside width of the bracket is exactlyinch 23? 3 Last question: What is the diameter of the pins or the holes that the pins fit through that hold the steps to the bracket? Thanks so much.

asked by: Steve J

0

Expert Reply:

I went to our warehouse and measured the TorkLift GlowStep Stow N' Go Mounting Bracket # TLA7810 to confirm the dimensions you inquired about.

The thickness of the side bracket material is indeed 1/4-inch. The space inside (between) the two side brackets is 22-5/8-inches; the outside width at the side brackets is 23-1/8-inch and the pin hole diameter is 1/4-inch.

expert reply by: Adam R

0

Answer 1

What's the entry height of your Lance? I am sure we have a set of the Torklift Glowsteps that will work but we need to know for sure the entry height to pick out right size. For example, the part #TLA7844 fits the height range of 31-42 inches.…

view full answer...

Answer 2

I recommend using the TorkLift GlowStep Camper Scissor Steps w/ Landing Gear - 4 Steps - 20" Wide - 375 lbs #TLA7804-8000. These are a 4 step system that has glow tape on the steps to help with visibility at night, and the adjustable landing…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 10

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 11

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 12

Thanks for the picture! For your 2023 GMC Sierra 1500 with adaptive ride control you'll want the Air Lift LoadLifter 5000 Air Helper Springs item #AL57388. This air bags have a 5,000 lbs load leveling capacity that will keep the rear end of your…

view full answer...

Dimensions of TorkLift GlowStep Stow N' Go Mounting Bracket TLA7810

Product Page this Question was Asked From

Continue Researching