Dimensions Of Winch Base For Fulton High-Performance 2-Speed Trailer Winch - Item # F142416

Question

Question:

Dimension of winch base?

asked by: Tom

0

Expert Reply:

The base of the Fulton High-Performance 2-Speed Trailer Winch, Item # F142416, is 5-3/4 inches wide by 6-7/8 inches long.

I have attached a link to a review video that has more information for you to check out.

expert reply by: Brint H

0

Answer 1

Fulton winches like the Fulton XLT 2-Speed Trailer Winch with Heavy Duty 20' Strap part #F142418 are made in Mexico according to Fulton. If you are looking for a winch made in the USA you may consider the Dutton-Lainson Covered Hand Winch part…

view full answer...

Answer 2

While I cannot find the exact specifications for the hole pattern on the Fulton 142208 I was able to find dimensions for the Fulton High-Performance 2-Speed Trailer Winch #F142416. It is going to have the same bolt pattern as the Fulton Winch…

view full answer...

Answer 3

The Dutton-Lainson Covered Hand Winch #DL17085 is 13-1/2" long/wide when looking at the side. I added a review video of this winch that shows more of its measurements for your to check out.

view full answer...

Answer 4

The bolt hole spacing as well as the bolt hole pattern is different when you compare the #DL14627 (which is the 1802A) to the #DL15440 (3200A). The overall dimensions differ as well. I am attaching some pictures showing the bolt hole measurements as…

view full answer...

Answer 5

I attached a picture that shows the dimensions of the JIF winch #315-W2500D as well as another picture that shows the overall dimensions of the jack.

view full answer...

Answer 6

Generally when picking out a winch for a boat trailer the ratio is 2 to 1 meaning you would need a winch with roughly half the capacity as the weight of the boat. With good rollers and a short winching distance the ratio increases to 3 to 1, but with…

view full answer...

Answer 7

Yes, the Hand Winch Strap with Safety Hook part #DL24251 will work just fine with the Dutton-Lainson Hand Winch part #DL14725. However, please note that you will be limited to the weight capacity of the winch which is 2,000 lbs because it is lower…

view full answer...

Answer 8

The mounting pattern for the Dutton-Lainson Hand Winch - TUFFPLATE Finish - 2 Speed - Direct Drive - 2,000 lbs #DL14725 you were looking at is the exact same as your current DL1802A, but the overall dimensions of the winches are different. The…

view full answer...

Answer 9

To get the cable to come off of the Dutton-Lainson Worm Gear Hand Winch, item #DL10974, you would need to crank the winch until the cable is all the way unwound from the winch drum and then continue cranking in the same direction until the cable is…

view full answer...

Answer 10

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 11

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Dimensions Of Winch Base For Fulton High-Performance 2-Speed Trailer Winch - Item # F142416

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching