Could Fulton F2 Trailer Jack Fit Trailer that Has Mounting Plate Currently Installed

Question

Question:

I have a ranger trailer with mounting holes that measure 3 x 5 1/2 on center. Do you have a jack with that hole pattern like the fulton f2

asked by: Ryan H

0

Expert Reply:

The Fulton F2 jack part # F1413140334 that you referenced could possibly fit your trailer frame but we don't have a way to match it to the mounting holes you mentioned as it's mounting holes are 4-1/2 inch by 5-1/2 inch.

This can fit most trailer frames that are 4 to 5 inches in height, or you could weld it directly to the trailer frame.

expert reply by: Jameson C

0

Answer 1

You can still install the tie-downs, but since the installation hardware used for the BoatBuckle G2 Tie-Downs #IMF14220 is 3/8 inch in diameter, the 1 inch transom strap holes on your trailer will be too large to install these tie-downs. The best…

view full answer...

Answer 2

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 5

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 6

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 7

You can add larger wheels and tires to a trailer as long as you have enough room for the larger size. The main clearance issues we find when putting larger tires and wheels on a trailer is from the top of the tire to the fender and from the inside…

view full answer...

Answer 8

Tire designations ST205/75D14 and ST205/75R14 are both for special trailer tires with a 205mm width, 75-percent aspect ratio and that fit a 14-inch wheel. The difference between them is the tire's type of construction. The ST205/75D14 tire is a…

view full answer...

Answer 9

We have an aluminum 7 spoke 14 inch trailer wheel that looks pretty close to the wheel in the picture you sent us, but it's not an exact match. For that wheel you would want the part #AM22329. For a 205/75R14 you can use #AM10234 or tire #AM10229…

view full answer...

Answer 10

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I am…

view full answer...

Answer 11

Long story short, yes you can. But going with the ST205/75R14 would be a better replacement than a ST205/75D14 because the R in the first size means it is a radial tire whereas the D in the second size means it is a bias ply. The main difference…

view full answer...

Answer 12

I am sorry I don't have any tires that are going to fit your rim. I do have a couple of comparable size tires that come in a wheel tire combo. I have listed the two below along with their lug patterns. 5 on 4-1/2 Lug Pattern - Kenda 205/65-10…

view full answer...