What is the Capacity of Gooseneck Coupler Head Kit, # GC-HEAD

Question

Question:

What is the weight rating of P/N GC-HEAD?

asked by: Evan

0

Expert Reply:

The Gooseneck Coupler Head Kit, # GC-HEAD, was designed for use with GCPN Series, GCSQ Series, and GCSQTW Series couplers which range in capacity from 25,000 to 30,000 pounds. So the maximum would be 30,000 pounds.

expert reply by: Michael H

0

Answer 1

According to the manufacturer the Gooseneck Coupler Head Kit #GC-HEAD is made from mild cast steel.

view full answer...

Answer 2

If you need to only replace the coupler, I'd recommend the Gooseneck Coupler Head Kit, #GC-HEAD, for etrailer or Ram replacement couplers or the Bulldog Gooseneck Coupler Repair Kit, #BD0287740300, for Bulldog couplers. To replace your…

view full answer...

Answer 3

Great question. As a general rule, when your trailer is loaded to it's full capacity, there should be a minimum clearance of 3 inches between the top of your tire and the underside of your fender.This should give you adequate clearance for…

view full answer...

Answer 4

The Timbren Axle-Less Trailer Suspension System - Straight Spindle Only - 3,500 lbs #ASR3500S05 has a deflection of 1-3/4 inches. I've attached a photo to assist. We recommend 4 inches above the tire in most cases for fender mounting to account…

view full answer...

Answer 5

Yes, the Gooseneck Coupler Head, part #GC-HEAD, fits on a standard 2-5/16 inch gooseneck ball.

view full answer...

Answer 6

The Bulldog Coupler Repair Kit BD0287740300 is designed for a round coupler so if you have a square tube you'll have better luck with the Gooseneck Coupler Head Kit #GC-HEAD. This is designed around etrailer and RAM round and square gooseneck…

view full answer...

Answer 7

I have included a picture showing how the parts of gooseneck coupler #GC-HEAD go together. They would be welded to the coupler tube in this configuration. Welding should be done by a professional welder. There are no specific instructions for the…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

What is the Capacity of Gooseneck Coupler Head Kit, # GC-HEAD

Product Page this Question was Asked From

Continue Researching