Availability of Dexter Axle Brake Assemblies K23-026-00 and K23-027-00

Question

Question:

I actually have 5x5 wheels so I'm not sure how that will affect those part numbers you supplied?

asked by: Dan W

0

Expert Reply:

We do have the regular Dexter Axle brakes and their Nev-R-Adjust equivalents.

The regular (manually adjusted) brakes that you are wanting are listed as part # 23-26 for the Left Hand side and part # 23-27 for the Right Hand side. Their Nev-R-Adjust equivalents are parts # 23-468 and # 23-469 respectively.

The Dexter Axle hub and drum assemblies that we have for a 3,500 lb axle use the Inner Bearing # L68149 and Outer Bearing # L44649. If you have a 5 on 4-1/2" bolt pattern then you want assembly # 84546UC3 for a standard spindle or part # 84546UC3-EZ for an EZ Lube spindle. If instead you have a 6 on 5-1/2" bolt pattern you want the assembly # 84656UC3 for a standard spindle or part # 84656UC3-EZ for an EZ Lube spindle.

I have attached some videos for you to check out as well.

expert reply by: Jon G

0

Dan W.

3/28/2018

I actually have 5x5 wheels so I'm not sure how that will affect those part numbers you supplied?

Reply

Jon G.

3/28/2018

For the Dexter Axle hub and drum assemblies that use the same bearings we have part # 84556UC3 for the standard spindle and part # DX68XR for the EZ Lube spindle. Both of these assemblies have a 5 on 5" bolt pattern like you mentioned you have.

Reply

Answer 1

The Dexter Hub and Drum assembly 8-247 you have on your Dexter P-11 3000lb axle use 10" x 2-1/4" brake assemblies. The correct replacement assemblies for your hubs is the Dexter Electric Trailer Brake Kit - 10" - Left and Right Hand…

view full answer...

Answer 2

The Dexter 3,000 lb trailer axles use a different size of brake assemblies so what you'd need is the Dexter 3k axle brake assemblies part #K23-472-473-00. 3,500 lb trailer axles use a slightly different size assembly so they would not fit. Then…

view full answer...

Answer 3

If the measurements on your trailer match the 4-Leaf Double-Eye Spring, part #e54SR or part #e28SR, they will bolt up to your trailer. My contact informed me that the heavier 4-Leaf Double-Eye Spring, part #e28SR will work, but it will give you a…

view full answer...

Answer 4

The brake mounting flanges, whether they be 4 or 5 bolt, have a standard hole spacing to fit their appropriate brake assembly. No worries about the brake assembly matching with the existing one on your axle. A 3500 lb axle like what you have will use…

view full answer...

Answer 5

Based on my research the Shelby 5101 is an A-frame coupler with a 2" ball and 5,000 lb capacity. We have exactly that with the A-Frame Coupler #CA5100B, which has a trigger latch and has a black paint finish. The same coupler is available with a…

view full answer...

Answer 6

I do have a couple possible solutions for raising your pontoon trailer, however increasing the shackle strap size will not be your best option. A more efficient way for raising the suspension on the trailer will be to use longer hangers. Unlike…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

It's totally normal for a bit of movement between any fifth wheel hitch and the base rails. The feet on the hitch are typically a bit smaller than the slots they slide into for mounting otherwise you'd have a hard time getting your hitch in…

view full answer...

Answer 9

The B&W Companion OEM 5th Wheel Trailer Hitch #BWRVK3700 is perfectly compatible with cushioned pin boxes like your MORryde RP072-1621HD, so the clunking you're experiencing isn't related to the two components being incompatible. With…

view full answer...

Answer 10

While we don't have any custom fit trailer wiring harnesses that fit the 2011 Isuzu NPR we can still help with a universal fit option like the #C56175 which you'd have to wire to the taillight circuits of your NPR.

view full answer...

Answer 11

For replacement Dexter manual adjust brake assemblies to replace your 36-19 you would want the part #23-27 for the right hand side and part #23-26 for the left hand side. These are manual adjust 10 by 2-1/4 inch Dexter brake assemblies that would…

view full answer...

Answer 12

There are 2 different capacities independent of each other though related. Tongue weight is the downward force or weight on the trailer hitch. So it is pushing down at the back of the vehicle. The gross trailer weight is the weight of whatever it is…

view full answer...