Boat Trailer Guide-Ons Without 90-Degree Angle Bend

Question

Question:

need one galvanized trailer guide post. The one i see on your web site is at 90 degrees angle. Mine are at a wider angle. do you have different units available?

asked by: Roger

0

Expert Reply:

You are right that most boat trailer guide-ons are 90-degree types. Some, like the Fulton Galvanized Roller Guide-Ons # FBGR200101 and CE Smith Bunk-Style Guide-Ons # CE27600 and # CE27660 have a wider angle. All such items are shown on the linked pages.

expert reply by: Adam R

0

Answer 1

Yes, the CE Smith Bunk-Style Guide-Ons for Boat Trailers - 60" Long - 1 Pair #CE27600 can work on the inside of a pontoon boat. Based on the photo you may prefer the CE Smith 90-Degree Bunk Board Guide-On Kit #CE27600K90 which will…

view full answer...

Answer 2

First you are going to need to determine if your particular winch can be used with a strap instead of a cable. Some winches will accept either but other winches must be used with one or the other. Contact your winch manufacturer to determine if…

view full answer...

Answer 3

That's a good question, and yes, the U-bolts will fit your 3" x 1-1/4" channel frame for the CE Smith guide-ons you asked about, which are the following part number: - CE Smith Post-Style Guide-Ons for Boat Trailers #CE27620…

view full answer...

Answer 4

The overall width of the CE Smith Multi Sport Plus Boat Trailer with Bunks #CE48870 is 54 inches wide.

view full answer...

Answer 5

The speed rating of the CE Smith Multi Sport Plus Boat and Kayak Trailer w/ Bunks #CE48870 is 65 mph due to the tires that are on it. If you needed to go faster than that you can swap the tires out to the part #TT48012C which is the same size but…

view full answer...

Answer 6

Since the outside frame channel on your trailer is about as wide as your boat you'd need to go with a guide on that has a 90 degree angle for the upright posts instead like the part #CE27600K90 so that you'll get closer contact like…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Boat Trailer Guide-Ons Without 90-Degree Angle Bend

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching