Recommended A-Frame Trailer Jack to Replace Existing Jack with Small Diameter Coupler Mount
Question:
Looking for an A Frame trailer jack for a 1948 Mobile Sportsman camper. Diameter of inside tube is only 1-1/4. Are there any trailer jacks made with that small of an inside tube? Camper weigh 2000#. Thank you for any info you can offer!
asked by: Tami R
Expert Reply:
Most jacks have an outer tube diameter of 2-1/4 inches. We do have a jack that is slightly smaller with the outer diameter being 2 inches. It is the Dutton-Lainson A-Frame Trailer Jack # DL22530. This will be a great option for your 1948 Mobile Sportsman Camper but you will need to enlarge the hole on your A-frame coupler. I recommend using a rotary tool like a Dremel or a hole saw to enlarge the opening in your coupler for proper mounting. Then you can use the caster # DL22414 or foot plate # DL22541.
The 1-1/4 inch trailer jack is definitely not industry standard anymore and we don't have anything really even close to that. If you need additional support in your coupler, you can use the Bottom Support Plate # DL22763 and weld it to the bottom of the coupler.
Products Referenced in This Question
Removable Wheel for Dutton-Lainson A-Frame Trailer Jack Model 6418
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Jack Wheel
- Wheel w Caster Assembly
- Dutton-Lainson
more information >
Removable Steel Foot with Pin for DL22530 A-Frame Trailer Jack by Dutton-Lainson
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Jack Foot
- 1-3/4 Inch Diameter Tubing
- Dutton-Lainson
more information >
Bottom Support Plate for A-Frame Trailer Jacks by Dutton-Lainson
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Mounting Hardware
- Plates
- Dutton-Lainson
more information >
Product Page this Question was Asked From
A-Frame Trailer Jack - Sidewind - 1,000 lbs. by Dutton-Lainson
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- A-Frame Jack
- Leveling Jacks
- Tongue Jacks
- Steel
- 0 - 1000 lbs
- Sidewind Jack
- 15 Inch Lift
- Bolt-On
- Weld-On
- No Wheel or Foot
- Dutton-Lainson
more information >
Continue Researching
- Shop: Bottom Support Plate for 2-1/4" OD A-Frame Jacks - 5,000 lbs
- Video: etrailer Trailer Jack JSP-100 Review
- Shop: Bottom Support Plate for A-Frame Trailer Jacks by Dutton-Lainson
- Search Results: bottom mount coupler
- Search Results: flat mount coupler
- Shop: B&W Pintle Hook Mounting Plate for 2" Hitches - 13" Shank - 14 Hole - 16,000 lbs
- Search Results: bwpmhd14004
- Shop: RV Jack Pads
- Shop: SnapPad XTRA Jack Pads for Lippert Leveling Systems w/ 9" Round Jack Feet - Qty 4
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Search Results: 68149
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Video: Choosing the Right Trailer Wiring
- Article: Trailer Maintenance Schedule
- Q&A: Adding Brakes to a Mobile Home Axle
- Video: Titan Trailer Brakes T2385200 Review
- Search Results: 44649
- Shop: Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles
- Shop: Trailer Wiring
- Search Results: 25580
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Fifth Wheel Hitch
- Shop: Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Brake Controller
- Search Results: 10~51
- Video: Lock N Roll 3-Position Channel Articulating Hitch Review
- Q&A: Wheel and Tire Recommendation For Jet Ski Trailer with Tire Size ST175/80R13