Dimensions of Buttons in Tow-Rax Mounting Buttons Kit

Question

Question:

The mounting buttons for tow-rax wall mounted folding table, look like they might be the item we need for another application. Is there any way you could get me the dimensions of the 3mm buttons so I could compare it to our drawing of what we are looking for?If they are a match or are real close, I would need 3,000 buttons. Thanks

asked by: MIKE H

0

Expert Reply:

I went out to the warehouse to take a few measurements of the buttons that are included with the Mounting Buttons Kit # TWSP25BK that you referenced. The overall, outside diameter of the button is 1.19 inches, while the smaller circle that jets out features a 0.89 inch diameter. The overall depth is 0.38 inches.

I have attached an image with these dimensions labeled that you can also take a look at. If you need any additional measurements, please let me know and I will be happy to take them. 4 buttons and 4 mounting screws are included in the kit.

expert reply by: Chris R

0

click to enlarge

Answer 1

The Tow-Rax Wall Mounted Folding Table - Aluminum - 45-1/2" Long x 18-1/2" Wide #TWSP45HFTA has the key hole shaped mounting slots to fit over screws, buttons, or pins and remove table by lifting up to release. I've attached…

view full answer...

Answer 2

There may be a solution for you though the Traffic Cone Holder for E-Track or Rack'em Spare Tire Holder #RA-26 does not have a specific weight rating for one of the brackets. There are a couple options for you to consider like the…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 8

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 9

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Dimensions of Buttons in Tow-Rax Mounting Buttons Kit

Product Page this Question was Asked From

Continue Researching