Fairing Recommendation for 2017 Mazda CX-5 with Factory Crossbars

Question

Question:

I have a 17 CX-5 with an OEM rack and it makes a lot of wind noise over 30 MPH. Can you recommend a fairing that would hopefully knock some of that noise down?

asked by: David O

0

Expert Reply:

The Inno fairings are designed to fit most crossbar dimensions. So the 48 inch long Onno fairing part # INA262 would fit and do a great job reducing the wind noise created by your crossbars. It will divert air over the bars which means considerable less wind noise.

expert reply by: Jameson C

0

Answer 1

The great thing about the Yakima roof fairings is that there are several lengths available and they mounting hardware allows it to fit all crossbar dimensions. The trick to picking out the correct size is to measure the distance between the feet of…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 5

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 6

Yes, your kick sensor for your hands free liftgate will still work after installing a Class III receiver on your 2024 Toyota RAV4 XSE. I have linked an install video near the bottom of the page for our etrailer Trailer Hitch Receiver #e23ZR being…

view full answer...

Answer 7

Hey Alec, For your 2016 Ford Fusion I recommend the recommend a roof rack from Inno: Inno Aero Crossbars #INXB138-145 Inno Through Feet for Aero Crossbars #INXS250 Custom Fit Kit for Inno XS200, XS250, and INSU-K5 Roof Rack Feet #INK860 As with any…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Thanks for all the details! We definitely have a way to get a cargo basket and an awning installed on your 2024 Toyota Highlander, although the aftermarket roof rack systems will use a clamping system with your door jambs instead of mounting via…

view full answer...

Answer 11

The Rhino-Rack Roof Rack for Factory Tracks #Y02-490B-NT is going to be your best bet for the tracks on the ARE topper for your 2012 Toyota Tacoma. The weight capacity is 220 lbs like you mentioned, but that's going to be the highest you'll…

view full answer...

Answer 12

If you are using the Rhino-Rack Aero Bar Crossbars like #RRVA137B they have a dimension of 54" long x 3-1/8" wide x 1-3/16" tall which works for Thule boxes that use the PowerClick quick-release clamps, including the Thule Vector…

view full answer...