How to Determine the Correct Replacement Steps for 2017 Winnebago Winnie

Question

Question:

Thanks for getting back with me. The steps that I would like to use as a replacement step for our Winnebago Winnie Drop are manual steps. I forgot to include the word "Drop" for the description of our travel trailer. The bolt pattern on the frame, however, is 26" across and 4" deep. So, which manual double step unit would recommend to replace our single step unit? Again, thanks for any advice you could provide me.

asked by: Ron S

0

Expert Reply:

In order to determine which double steps to use with your 2017 Winnebago Winnie you will need to know the mounting bolt pattern of your current steps. For example, the Lippert Kwikee 32 Series # LC3722617 has a mounting bolt pattern that is 22" wide x 8" deep. The Lippert Kwikee 40 Series # LC3726891 has a slightly different mounting bolt pattern of 26" wide x 8" deep.

If you let me know what your mounting bolt pattern is I would be happy to make a recommendation for you; I've added a link to our selection of double steps for you to check out as well.

expert reply by: Kyle S

0

Ron

3/20/2018

Thanks for getting back with me. The steps that I would like to use as a replacement step for our Winnebago Winnie Drop are manual steps. I forgot to include the word "Drop" for the description of our travel trailer. The bolt pattern on the frame, however, is 26" across and 4" deep. So, which manual double step unit would recommend to replace our single step unit? Again, thanks for any advice you could provide me.

Reply

Kyle S.

3/20/2018

Thank you for the dimensions, and though there may be a solution for you, I took a look at each of the manual double steps we carry and none of them have bolt hole centers of 26" wide x 4" deep. You may be able to use the TorkLift GlowStep Revolution Scissor Steps w/ Landing Gear # TLA8102 if your Winnie has 25-1/2" of space between factory mounting brackets. These steps have mounting base dimensions of 25-7/16" wide x 12" deep, step platforms which measure 22" wide x 8" deep, a drop/rise of 7-1/2" and are 11-1/2" - 12-1/2" when collapsed with a height of 18-1/2" - 24" from the top of step opening to the ground. Model # TLA8002 is the same double step that will fit if you have 25-1/2" of space between your factory mounting points but has mounting base dimensions of 27-7/16" wide x 12" deep and are 13-3/4" - 14-3/4" when collapsed with a height of 25-1/2" - 32" from the top of step opening to the ground. I've added links to video reviews of these steps for you to take a look at.

Reply

Answer 1

I looked up pictures of your 2001 Winnebago Minnie Winnie 22R and it has a cut out for a single step below the door. The Flexco Manual Pull Out step part #SMFP-1100 was designed to fit RV setups just like yours but you'd want to measure first to…

view full answer...

Answer 2

Yes, the Ventline Ventadome Roof Vent part #V2119-603-00 is designed to wire to a switch like the one you mention part #VC0533-03-A. I have attached a wiring diagram for your reference. The Ventadome Roof Vent also comes in white part #V2119-601-00.…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

The 07100 bearing number you referenced is an older bearing that has the same dimensions as #L44643. If both the inner and outer bearings on your existing trailer are the 07100/ #L44643, and the hub has a 4 on 4 inch bolt pattern, the correct…

view full answer...

Answer 6

The Trailer Hub and Drum Assembly part #AKHD-545-35-K is the correct replacement for an AL-KO 7230. In regards to the braking assemblies, I suggest getting a new pair, the Electric Trailer Brake Kit part #AKEBRK-35-SA. This option will save you some…

view full answer...

Answer 7

For a replacement step for what you have now that shows part number 725-0042 the correct set is the Kwikee 32 Double Step part #LC3722617.

view full answer...

Answer 8

The best option we have for you is the 3-Leaf Double-Eye Spring part #e84SR with the Single-Axle Trailer Hanger Kit part #APS4. This option will replace the leaf springs and leaf spring hanger brackets which is needed because the new double eye leaf…

view full answer...

Answer 9

The Kwikee 32 Series Double Step part #LC3722617 that you referenced is a replacement for the Coach step you have now. You will have to cut that wire that runs to the old module and splice it to the new module.

view full answer...

Answer 10

If you are looking for a replacement step setup the number on the step that I can see corresponds to a Lippert Kwikee 32 Series Electric Step #LC3722617 which is a powered double step for RVs like your 2007 Georgetown.

view full answer...

Answer 11

Hey William, the E6 error on a Furrion wall thermostat indicates an Open circuit Humidity Sensor issue. Most likely the sensor is bad and needs to be replaced as this is a pretty rare error code.

view full answer...