What Is Weight Of Square Direct Weld Jack Item # TJD-7000S

Question

Question:

Hello. Please, I need to know the weight of the Trailer Jack - TJD-7000S. Thank you very much.

asked by: Jorge S

0

Expert Reply:

I do not have the exact weight of the Square Direct Weld Jack with Footplate, Item # TJD-7000S. However, it has a shipping weight of 24-lbs so it weighs around 20-lbs to 22-lbs.

If you need to know weight capacity then it has a lift capacity of 7,000-lbs and a support capacity of 8,000-lbs.

Let me know if you have other questions and I will be glad to answer them.

expert reply by: Brint H

0

Answer 1

The big difference is the orientation of the foot plate on both jacks. One just has the rectangular shaped foot plate rotated 90 degrees from the other. Aside from that they both have the same capacities and travel.

view full answer...

Answer 2

Yes, the channel of the Curt Channel Style Adjustable Ballmount #C45901 that you referenced is compatible with the Replacement 2" and 2-5/16" Dual-Sided Hitch Ball #C45912.

view full answer...

Answer 3

I spoke with my contact at Ram and they said that the internal screw for the 7K jacks are not something they carry replacements of so you will need to replace the whole jack. Even if this wasn't the case it would be a good idea to replace the…

view full answer...

Answer 4

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 5

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 6

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 7

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 8

The #37213635 JR Products Replacement Landing Gear Switch you'd mentioned would be a proper replacement for your existing Atwood 70254 landing gear switch. If you wanted the switch, wiring harness and the bezel for the switch, use the Stromberg…

view full answer...

Answer 9

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...