Weight Distribution Shank Recommendation to Fit 2-1/2 inch Hitch

Question

Question:

I have a weight distribution system of yours now that fits 2inch receiver. I now need for 2-1/2 receiver or class 5. New Ford pick up. I have a picture of exactly what I need but dont know how to get it to you.

asked by: Jeremy S

0

Expert Reply:

Feel free to email me back with the picture, but I believe you are in need of a shank designed for your new 2-1/2 inch trailer hitch like the part # C17131 which fits all of the weight distribution systems we carry as well as a 2-1/2 inch hitch

expert reply by: Jameson C

0

Answer 1

Most weight distribution brands use the same dimensions for their shanks so they are interchangeable. If the holes on your shank are 3/4 inches in diameter and are 1-1/4 inch apart on center then we have shanks that will work. I attached a picture…

view full answer...

Answer 2

Most of the weight distribution shanks like the #C17131 that you referenced are compatible with the heads of different brands systems. If the distance between the mounting holes on the shank you currently have are 1-1/4 inches apart and are 3/4 inch…

view full answer...

Answer 3

The Curt weight distribution shanks for 2-1/2 inch hitches also fit the Husky systems so if you don't need much drop the part #C17131 would be what you'd need or if you need a decent amount of drop you'd want the #C17132.

view full answer...

Answer 4

Normally an intermittent working motorized jack like the Lippert Components Powered Tongue Jack #LC285318 is due to a faulty ground or a short circuit in the power wire. I recommend checking your ground connections, normally in the mount of the jack…

view full answer...

Answer 5

The Curt weight distribution shank part #C17131 that you referenced would be exactly what you'd need. This is compatible with your Pro Series weight distribution system since they both fit the same drop shank dimensions and it fits a 2-1/2 inch…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Weight Distribution Shank Recommendation to Fit 2-1/2 inch Hitch

Product Page this Question was Asked From

Continue Researching