Availability of 12 inch Brake Assemblies that Have 4 Bolt Mounting Pattern

Question

Question:

I have an older trailer with what I believe to be mobile home axles. They are 12x2 which many of yours appear to be, however they only have a 4 bolt pattern instead of a 5. Would you happen to carry any that are 5 bolt?

asked by: Jonathan P

0

Expert Reply:

The Dexter brake assemblies part # 23-105-106-09 can mount to the AL KO 4 bolt mounting flange. If the upper mounting bolt holes are further apart than the lower bolt holes these assemblies will fit and work well.

expert reply by: Jameson C

0

Answer 1

For your 12x2 electric brake assemblies, I recommend the Dexter Electric Brake Kit for 4 Bolt or 5 Bolt Flange - 12" - Left/Right Hand Assemblies #23-105-106-09. These assemblies will fit your 4 bolt flange and will work well on your trailer.…

view full answer...

Answer 2

Most likely the #23-105-09 and #23-106-09 would work well for you, but you need to verify one more thing. Does the current brake assembly you have attach to the axle with 5 nuts? If so, then you have the standard bolt mounting pattern these two would…

view full answer...

Answer 3

When it comes to brakes for your boss's older Flying L gooseneck horse trailer, I believe that I have exactly what you are looking for, #23-105-09 and #23-106-09 for a 6,000 lb axle. I have included a picture which includes the mounting hole…

view full answer...

Answer 4

We do offer 12 x 2-inch electric brake assemblies with a 4-bolt mounting flange. Dexter parts #23-106-09 and #23-105-09 are right- and left-hand brake assemblies that have dual mounting hole patterns, both 5-hole and 4-hole. These brakes are rated…

view full answer...

Answer 5

The Dexter Braking Assemblies like the #23-464-465 are widely regarded as the highest quality assemblies due to them being manufactured right here in the USA and using the highest quality materials available. With that said we have sold a lot of the…

view full answer...

Answer 6

The #23-105-09 would work well since the dimensions and bolt pattern are correct for your Hayes 7k setup. Typically brake assemblies in this size will have weight ratings that range from 5,200 up to 7k so the #23-105-09 will work well as they match…

view full answer...

Answer 7

All of our 12 x 2-inch 6K-rated electric trailer brakes are shown on the linked page. Most of these use the 5-bolt mounting pattern but a few Dexter products include holes for BOTH bolt patterns, both 5-bolt and the 4-bolt Hayes/AL-KO pattern, parts…

view full answer...

Answer 8

Dexter hub #8-174-5UC3 uses the 5-spoke utility bolt pattern so it is uncommon just like the hub you have. If your existing hub uses inner bearing 25580 and outer bearing 15123 with a seal inner diameter of 2-1/8 inches then this hub is a likely fit.…

view full answer...

Answer 9

I have just what you need, the Dexter Electric Brake Kit for 4 Bolt or 5 Bolt Flange part #23-105-106-09 which is our best and only available option. The four brake mounting flange with offset holes is very uncommon but we do thankfully still have an…

view full answer...

Answer 10

The center hole of the brake assemblies #23-105-09 and #23-106-09 measures 3-3/16 inches across. The kit for both of these is the part #23-105-106-09 that you referenced.

view full answer...

Answer 11

I've linked you to an FAQ article that explains how to determine your wheel bolt pattern. The 4 bolt brake mounting flange has a standard bolt pattern of 2-7/8 inches center to center between adjacent holes or 4 inches center to center measured…

view full answer...

Answer 12

EZ lube spindles are more than just a zerk fitting attached to the end of the spindle. There would need to be a hole in the spindle between where the bearings ride for the grease would then fill the hub by. To be perfectly honest using EZ lube…

view full answer...

Availability of 12 inch Brake Assemblies that Have 4 Bolt Mounting Pattern

Product Page this Question was Asked From

Continue Researching