Anti-Rattle Lock for Original Thule Vertex 4 Bike Trailer Hitch Bike Rack

Question

Question:

I am looking for an anti-rattle lock with cable for my Thule Vertex 4 bike rack. This hitch rack fits a 2inch receiver and is an older version that doesnt come with an integrated lock. which system do you suggest?

asked by: Moe

0

Expert Reply:

You'll want to get Thule's Snug-Tite set, part # THSTL2, which will add a locking anti-rattle hitch pin to your rack. You can then add a traditional cable lock like part # e98891 and link the bikes together to either the safety chain loop of your hitch or the Vertex itself to add the locking security you're looking for.

expert reply by: Jacob W

0

Answer 1

Here at etrailer, we do not recommend using two hitch adapters at the same time. Not only does it reduce the weight capacity of the hitch even more (more than the 50% from using one adapter), it can be dangerous for other motorists. In addition, we…

view full answer...

Answer 2

Using a hitch extender does cut the tongue weight capacity of the vehicle it is installed in by 50 percent. Since yours is rated for 350 lbs you'd be limited to 175 lb but we do have a 14 inch hitch extender with the Gen-Y part #GY89SR which…

view full answer...

Answer 3

I do have an option for you but the angle piece from the Swagman Traveler XCS S64664 would not allow you to carry a bike rack and cargo rack at the same time. If you were able to make it work it would be very unsafe. I recommend to use the Malone…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Just looking at your Tern HSD bike with fenders, I'm going to say no the Saris MHS Bike Rack for 1 Bike #SAR23MR is not going to work. I did some research and it looks like a lot of Tern owner's went with the Hollywood Racks Sport Rider SE…

view full answer...

Answer 7

Yes, there is! It is the Draw-Tite item #76271. This hitch is custom fit for the 2024 Subaru WRX and bolts to it with included hardware. It is a class III hitch with a 2" receiver that has a 3,500 lbs towing capacity and a 525 lbs maximum tongue…

view full answer...

Answer 8

Thanks so much for the photos, they were very helpful, and based on that and the fact you mentioned it was from 2009, I am almost certain that what you have there is the Thule Roadway 914 bike rack. We do in fact have the correct 1-1/4" to…

view full answer...

Answer 9

I checked with my contact at Thule and verified that the Thule replacement hitch bolt you are looking for is part #908-1240-54. It is a 12 x 40mm hex bolt with a property class of 8.8. It should be installed with M12 washer, #951-1224-54, and M12…

view full answer...

Answer 10

There's not much of a difference in the 2" hitches available for the 2023 Toyota RAV4. The Draw-Tite item #DT82QR, Curt item #C13416, and etrailer item #e23ZR all look identical when installed. With this in mind, I recommend going with the…

view full answer...

Answer 11

The Thule Apex Swing XT #TH9027XT is a great option for a 2-inch hitch receiver. The nice thing about having the Apex's swing-away feature is that it lets you access your rear cargo area on your 2018 Subaru Outback Wagon without removing bikes…

view full answer...