Mounting Surface to Turnbuckle Hole of Brophy Tie Down HSAB

Question

Question:

Can you provide a dimension from the inside of the bedrail to the eyelet where the turnbuckle attaches? I am building a truck camper and need the dimension to locate the eyelet.

asked by: Bob B

0

Expert Reply:

The distance from where the Camper Tie Down part # HSAB mounts to a bed rail to the center of the hole for the turnbuckle measures 11-1/4 inches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Angled Hold-Downs #HSAB do not have a specific vehicle fit list but they are likely to fit your 2015 Chevy Silverado 1500. Installation of the hold-downs requires a minimum of 2" of clearance between the inside of the truck's sidewall…

view full answer...

Answer 2

The best option would be for you to use a hitch on your trailer, and Curt #13703 would be a great choice and will fit your travel trailer so long as it has a box frame, I-beam frame or C-channel frame and is between 22" and 72" wide. This…

view full answer...

Answer 3

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 4

The primary advantage of frame-mounted camper tie-downs like the TorkLift #TLF2012A and #TLF3001A, which are designed to fit your Ford F-350 if it has the 6-3/4 foot bed without a step/board underneath and a factory hitch, is the stability they…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Yes, the Brophy camper tie downs like the #HSAB can be used with bed rail covers. If you check out the picture I attached you can see a set installed on a bed rail with plastic covers.

view full answer...

Answer 7

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 8

There is no weight capacity for the Brophy Clamp On Camper Tie-Downs #HSSF. The tie-down hardware kit #TDHP, that is used to secure the camper to the #HSSF tie-downs has a weight capacity of 3,000-lbs. My contact at Brophy said the tie-downs will…

view full answer...

Answer 9

Yes, it will! The Hellwig Adjustable Big Wig Rear Anti-Sway Bar item #HE96XR is confirmed to fit your 2024 Chevy Silverado 3500. This sway bar will minimize lateral movement in your rear end and improve stability. This sway bar is made in the USA and…

view full answer...

Answer 10

The Brophy Slide In Camper Tie-Downs #HSAB might be a fit for your 2011 Ford F-150 but you'll need to do a bit of measuring first and you'll likely need to trim out holes where the tie-downs would sit. You'll want to verify that #HSAB…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Mounting Surface to Turnbuckle Hole of Brophy Tie Down HSAB

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching