Flexco Double Step Width Dimensions

Question

Question:

In Item # SMFP-2120 The 23 and 5/8 dimension, listed 2x, seems relatively a bit too large/out of proportion. Please verify...

asked by: Gino R

0

Expert Reply:

The 23-5/8 inch width is the widest point and is actually for the metal rod. The bracket width is 22-1/8 inches from edge to edge. I measured this product for you to confirm and have attached a photo to assist.

expert reply by: Jason S

0

click to enlarge

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Donald, the best Blue Ox weight distribution would be the pat #BXW0550 as it has a perfect tongue weight range for your 450 lb tongue weight trailer.

view full answer...

Answer 6

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 9

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 10

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 11

To install the Tekonsha Prodigy P3 Trailer Brake Controller #90195 in your Freightliner S2RV chassis the wiring is behind the kick panel in the drivers compartment. There is not a connector on the wires, they are simply terminated with tape. You will…

view full answer...

Answer 12

It's very easy to install a trailer brake controller on a 2021 Honda Ridgeline. I recommend the Tekonsha Prodigy P3 Trailer Brake Controller part #90195 which comes with a harness that you could simply attach to the one that came with the…

view full answer...

Flexco Double Step Width Dimensions

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching