Location of Factory Brake Controller Port on a 2007 Ford Explorer with Factory Tow Package

Question

Question:

I cant find the brake controller port on my 2007 Ford Explorer. I have the factory tow package but I have looked under the dashboard where is supposed to be and its not there?

asked by: Rich

0

Expert Reply:

If you have the factory 7-way connector on your 2007 Ford Explorer the factory brake controller plug will be located behind the glove box on the left side. You will open the glove box, push in the two tabs it rests on to get it to open further and the 6-pin connector is buried on the left hand side, close to the center console.

I am including a link to installation instructions on the Tekonsha Brake Controller Adapter, part # 3035-P that will show what the 6-pin connector will look like.

expert reply by: Jeff D

0

Michael M.

7/6/2020

2007 Ford Explorer with factory 7 pin plug (V8) cannot find plug behind (or around) glove box did find a similar plug(Gray) underneath steering wheel (has 5 of six pins with one "blank" spot) looks Colored wires leading to plug are red, blue, purple/white, brown, and black/white

Reply

Answer 1

I am not sure of the particular video you are referring to, but if your 2007 Ford Explorer Sport Trac is equipped with the 7-Way connector, then installing a trailer brake controller is a simple, plug-and-play installation. For this application, you…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 11

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 12

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Location of Factory Brake Controller Port on a 2007 Ford Explorer with Factory Tow Package

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching