Recommended Trailer Hitch and Ball Mount for 2004 Dodge Durango
Question:
Hi, I am looking to buy a high and ball attachment for my 2004 Doge Durango SLT 4WD 4.7 gas engine. I will need to pull a 24-26 ft camper of around 7000 lbs. Thank You.
asked by: David
Helpful Expert Reply:
Starting with the trailer hitch (if you do not already have one), I recommend the Draw-Tite Class III Max Frame Receiver Hitch # 75292. This Class III hitch is confirmed to fit your 2004 Dodge Durango and will use existing holes in the vehicle's frame for a no-drill installation. This will provide you with a 2 inch receiver opening and the hitch features a 6,000 pound towing capacity and 600 pound tongue weight capacity. When used with a weight distribution system, the towing capacity increases to 9,000 pounds with a 900 pound tongue weight limit. I recommend taking a look at your copy of the vehicle owner's manual to verify its capacity, as it can vary depending on what model Durango you have. You will need to follow whichever capacity is lower, the vehicle's or the hitch.
I have attached the written installation instructions that you can take a look at.
For a ball mount and hitch ball, I recommend taking a look at the etrailer.com Ball Mount Kit for 2 Inch Hitches # 989900. This kit includes two different 2 inch ball mounts, each featuring a different rise and drop measurement (one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop). Both a 2 inch and 1-7/8 inch hitch ball are also included. With the 2 inch hitch ball, the ball mount has a towing capacity of 7,500 pounds.
When choosing a ball mount, it is important to pick out one that will give you the necessary rise or drop to tow your trailer level. I have attached a great article that explains how to determine this, along with a link that will take you to our available ball mount selection if the above mentioned kit does not include a sufficient rise or drop for your application.
Finally, if your Durango does not have the factory tow package and you do not yet have a trailer wiring connector installed, I recommend the Tekonsha T-One Vehicle Wiring Harness # 118390. This custom-fit harness will install by connecting directly to the built-in ports located behind the driver and passenger side tail lights. This will give you a 4-Way connector at the rear of the vehicle to connect with and power a trailer's basic signal lights.
I have included an installation video on your vehicle that you can use for reference.
If your trailer is equipped with brakes, you will also need the Universal Wiring Kit # ETBC7, along with a brake controller like the excellent Tekonsha Prodigy P3 # 90195. This wiring kit includes everything needed to install a fully functional 7-Way from the above 4-Way, along with the wiring needed to install the brake controller.
I have attached a couple articles and videos to assist with installation if needed.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- Tekonsha
more information >
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class IV
- 600 lbs TW
- 6000 lbs GTW
- 9000 lbs WD GTW
- 2 Inch Hitch
- 900 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Determining Towing Capacity for 2005 Dodge Durango
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Recommended Replacement Trailer Hitch Receiver for 2006 Dodge Durango
- Q&A: Does Curt Hitch # 13297 Extend Out Past The Bumper on a 2006 Dodge Durango
- Article: Trailer Wiring Diagrams
- Q&A: Recommended Replacement for Dometic Duo-Therm RV Air Conditioner
- Article: How to Install a Trailer Hitch
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Solution for Connecting 7-Way Trailer Connector to Aftermarket Trailer Hitch on 2005 Dodge Durango
- Q&A: Recommendation for Wiring Harness and 7 Pole Adapter for Towing a Trailer with My 2004 Dodge Durango
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Parts Needed to Tow a Trailer with Brakes Using a 2006 Dodge Durango
- Article: Determining Trailer Tongue Weight
- Article: Towing a Trailer? Let's Talk About Brake Controllers