Can a Timbren Suspension Kit be Used with Weight Distribution System

Question

Question:

on a 2017 4x4 1500 silverado crew cab with max towing can i use timbren with wdh i tow 30 ft tt i know you dont recommend on other vehicles

asked by: John

0

Expert Reply:

Yes, you can use a Timbren system like the part # TGMRCK15S with a weight distribution hitch on a 2017 Chevy Silverado 1500.

If you have the WD system already you'll have to go through the setup process again after the Timbren install since you'd need less spring bar tension.

expert reply by: Jameson C

0

Answer 1

For your 2012 Ram 2500, you are correct that either suspension enhancement system will work. However there are major differences between them functionally. The Timbren system #TDR2500CA is a very solid jounce spring. It is a strong Aeon hollow rubber…

view full answer...

Answer 2

I have used both RoadActive Suspension (RAS) and Air Bags; I don't think it's even close. The superior option is an air bag kit, the Air Lift LoadLifter 7500 XL Air Helper Springs part #AL57595. They are both going to provide support and…

view full answer...

Answer 3

The MB Sturgis Propane Hose Assembly - RV Type 1 w/ Back Check x 1/4" MPT - 12" #100473-12 are manufactured in St. Louis, MO.

view full answer...

Answer 4

Generally speaking, a properly rated and installed weight distribution system will not require the use of additional suspension enhancements. However, I am aware of the factory rear coil springs on your 2017 Ram 1500 and their tendency to sag.…

view full answer...

Answer 5

The Air Lift LoadLifter 5000 Air Helper Springs part #AL57385 should work on a 2020 Ford F-150 with lift but that really comes down to what the lift entails. That said, you will need a spacer in order to compensate for the lift. If the amount of rear…

view full answer...

Answer 6

The use of rear suspension enhancement along with a weight distribution kit is not recommended. They will tend to work against one another. If sag on your 2008 Ford F-150 is caused by a load or a fifth wheel or gooseneck trailer then suspension…

view full answer...

Answer 7

Yes, the Shocker Hitch Air Cushioned Trailer Coupler #SHK73RR can be used with a weight distribution hitch system. To use it with a hitch like the Equal-i-zer Weight Distribution System #EQ64FR you will need to follow these directions for inflating…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...