What Increments Does the B&W Tow & Stow 2-Ball Mount # BWTS10037C Adjust in

Question

Question:

it says it has a minimum drop of 5" and a maximum rise of 5-1/2". how far apart are the adjustment holes?

asked by: Phil

0

Expert Reply:

The B&W Tow & Stow 2-Ball Mount # BWTS10037C does have a Maximum Drop of 5" and a Maximum Rise of 5-1/2" just as you stated. The ball mount adjusts in 1" increments.

expert reply by: Jon G

0

Answer 1

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 6

It sounds like you could have a set of standard fifth wheel rails that most manufacturers use for their fifth wheel hitches to install into. The different manufacturers all make their own brand of rail kit, but they all have basically the same…

view full answer...

Answer 7

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The Patriot Slider part #BWRVK3270 might be a bit more noisy than the Companion slider part #BWRVK3400 due to the increased number of mounting points, 4 at the corners vs. 1 in the center. Probably not that noticeable and certainly not something…

view full answer...

Answer 10

Congrats on the new truck! To add a autoslider 5th wheel hitch you will first need to add a set of rails to your 2023 Ram 2500. There is no aftermarket way to add a puck system or below bed mounting method for an autoslider 5th wheel hitch. I…

view full answer...

Answer 11

Hi Robert, The Curt Pintle Hook #C45908 would require that your EZ Loader boat trailer has a lunette ring for the coupler. From what I can see the 26-30ET should have a surge brake coupler that would couple to a standard ball mount. You'll need…

view full answer...

Answer 12

We do have a full 5th wheel base rail and install kit for your 2024 Ram 3500, from Curt, and are the following part number: - Curt Custom Fifth Wheel Installation Kit for Ram #C16430-204 I verified directly with Curt that these fit your '24 Ram…

view full answer...

What Increments Does the B&W Tow & Stow 2-Ball Mount # BWTS10037C Adjust in

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching