Lock for Ram Truck OEM Fifth Wheel Hitch

Question

Question:

Do you have a 5th wheel pin lock for the OEM Ram hitch?

asked by: John W

0

Expert Reply:

The Ram OEM fifth wheel can be locked though there is not a specific lock designed for it. The Reese OEM 5th Wheel Hitch # RP30918 will need to be locked with a padlock such as the Master Lock Padlock # ML1KA in the place where the pin and clip are at the handle.

expert reply by: Kyle S

0

Answer 1

Thank you so much for the photos! They were super helpful, and I can verify for you that the correct touch screen panel for your Lippert 6-point leveling system is the part number you asked about: - Replacement Touch Screen Control Panel #LC83VR This…

view full answer...

Answer 2

The MORyde pin box RSPB83-1622 is a 16K orbital rotating pin box designed for increased turning clearances with short bed trucks. Although this nice feature is not required for a long bed truck like your 2017 Ram 3500 I recommend keeping it. The…

view full answer...

Answer 3

The #LC328492 Trail Air Flex Air Air Ride Pin Box you mentioned is not an extended pin box. When installed, the center king pin to first row of bolt holes in the turret would be right at 17-3/4 inches, as you can see in the provided diagram. I've…

view full answer...

Answer 4

I have attached for you below a dimensional drawing of the Lippert 1621 5th Wheel Pin Box part #LC1191191 which was provided by Lippert. This gives a frame of reference for the height by measuring from the bottom of the skid plate to the top of the…

view full answer...

Answer 5

I spoke with my contact at Lippert and he informed me that the app will ask you to set up a PIN initially and that you will then need to select the 3 digit number you want. If you selected a PIN already you would need to use the numbers you already…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

Answer 12

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Lock for Ram Truck OEM Fifth Wheel Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching