Recommended Wiring Harness Confirmed to Fit a 2006 Infinity FX35

Question

Question:

which trailer wiring kit fits 2006 infinity fx35

asked by: David P

0

Expert Reply:

For your 2006 Infinity FX35, we have the Tekonsha ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit # 119250KIT. This is a confirmed fit that uses zero contact interface sensors to capture the signal in the factory wiring to transfer it to your trailer wiring connection. This harness will give you a 4-way flat connection.

If you want to add a 7-way, the only way to do so is to use the # ETBC7 kit along with this 4-way to hardwire those other functions. If you want to use a brake controller with this vehicle, I recommend the Tekonsha Prodigy RF Wireless Trailer Brake Controller - 1 to 3 Axles - Proportional # TK94FR which won't require any changes to your factory wiring but will require the 12V power line to your 7-way along with a ground connection.

expert reply by: Jason S

0

Answer 1

Your brake lights and running lights are designed to be operated by two different circuits. You'll need to find the running light circuit in your trailer's wiring and then you'll need to run that circuit to the running light assemblies…

view full answer...

Answer 2

Based on the colors of the wires that are on the lights you bought for your trailer is sounds like the assemblies ground through the mounting hardware, the brown wire is the running light circuit, and the red wire is the stop turn circuit. A…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Recommended Wiring Harness Confirmed to Fit a 2006 Infinity FX35

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching