Could Hopkins Backup Sensor System # HM60100VA be Used on Front of Truck

Question

Question:

Is there any reason why this would not work on the front of my 2017 F250? Thanks!

asked by: Simon F

0

Expert Reply:

There's no reason the Hopkins Backup Sensor System # HM60100VA wouldn't work on the front of a vehicle like your 2017 Ford F-250. The install would be the same but you'd have to come up with a different circuit than the reverse light circuit for activating the alert.

expert reply by: Jameson C

0

Answer 1

The MORryde Wall RV TV Mount #MR57RR weighs 16lbs. It can support a TV that weighs up to 20lbs. The TV will need one of the following VESA patterns 100mm x 100mm, 200mm x 100mm, or 200mm x 200mm. Or you can use the VESA Adapter Plates #MR74RR to fit…

view full answer...

Answer 2

The Hopkins Backup Sensor System part #HM60100VA will install independently of the factory backup camera system. It does come with its own speaker but there is no way to integrate this into the vehicle's stereo if that is what you are asking nor…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

Hey Cody, you are installing this B&W Turnoverball #BWGNRK1020 on a 2021 Chevy 2500 correct? If so, the M14 bolts are definitely the correct size. It is possible that the holes in the frame are corroded which is preventing the bolts from…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

The Air Lift WirelessONE Compressor System #AL25980EZ and Air Lift WirelessONE Compressor System #AL25980 are nearly identical with only some very minor differences in CFM and duty cycle ratings. The #AL25980EZ will also come with an easier mounting…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The JR Products part #37207-31485 that you referenced is an exact replacement for your Flex Tech H72812-72 so it would work great. It's 72 inches long, 1/2 inch diameter, and has 3/8 inch fittings on both ends.

view full answer...

Answer 9

The rear suspension enhancement I recommend for your 2022 GMC Sierra 3500 when you are towing a 5th wheel hitch is the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers #AL88341. The LoadLifter 5000 Ultimate air…

view full answer...

Answer 10

The recommendation for the 10" diameter lube plate on a B&W Companion 5th Wheel Trailer has come from the manufacturer of the fifth wheel hitch, B&W. The Lube Plate for Reese 5th Wheel Trailer Hitches part #RP83002 will work just fine…

view full answer...

Answer 11

According to B&W the B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit part #BWGNRK1020 is about a 2 hour install by a professional. All the Hardware is provided. I have attached the installation instructions so you…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...