Can the Hopkins Backup Sensor System Be Tied Into a Factory Backup Camera System

Question

Question:

Can this be added connected to the factory backup camera of a 2017 GMC Terrain?

asked by: Tace

1

Helpful Expert Reply:

The Hopkins Backup Sensor System part # HM60100VA will install independently of the factory backup camera system. It does come with its own speaker but there is no way to integrate this into the vehicle's stereo if that is what you are asking nor am I aware of another system with this feature.

expert reply by: Conner L

1

Answer 1

The MORryde Wall RV TV Mount #MR57RR weighs 16lbs. It can support a TV that weighs up to 20lbs. The TV will need one of the following VESA patterns 100mm x 100mm, 200mm x 100mm, or 200mm x 200mm. Or you can use the VESA Adapter Plates #MR74RR to fit…

view full answer...

Answer 2

There's no reason the Hopkins Backup Sensor System #HM60100VA wouldn't work on the front of a vehicle like your 2017 Ford F-250. The install would be the same but you'd have to come up with a different circuit than the reverse light…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

Hey Cody, you are installing this B&W Turnoverball #BWGNRK1020 on a 2021 Chevy 2500 correct? If so, the M14 bolts are definitely the correct size. It is possible that the holes in the frame are corroded which is preventing the bolts from…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to B&W the B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit part #BWGNRK1020 is about a 2 hour install by a professional. All the Hardware is provided. I have attached the installation instructions so you…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

Hey David; I checked directly with Pace Edwards for you and can tell you that the rails on the Pace Edwards Switchblade Retractable Hard Tonneau Cover #PE46QJ will protrude just under 3/4" on both sides when installed on your Ford Super Duty…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Can the Hopkins Backup Sensor System Be Tied Into a Factory Backup Camera System

Product Page this Question was Asked From

Continue Researching