Weight of Demco Nissan Rail Kit Adapter and Capacity

Question

Question:

Does anyone make a 16K frame rail like the Demco Nissan 5th Wheel Rail Adapter # DM6200? How much does the DM6200 weigh?

asked by: Victor B

0

Expert Reply:

The Demco Fifth Wheel Rail Kit adapter for Nissans part # DM6200 weighs 95 lbs and has a 21k capacity so it would easily work with a 16k fifth wheel hitch.

expert reply by: Jameson C

0

Answer 1

The Demco 5th Wheel Rail Adapter #DM6200 for your 2018 Nissan Titan XD has the following measurements which I have also included in the picture as well. Center of hitch to front edge of adapter- 10-3/4" Hitch is 2-1/4" in diameter Center of…

view full answer...

Answer 2

I understand that your options may be limited with a short bed Nissan Titan xD with the factory Gooseneck and Pucks, but you do have the option of a no-drill installation with the Demco 5th Wheel Rail Adapter for Nissan Titan XD OEM 5th Wheel Towing…

view full answer...

Answer 3

The best fifth wheel hitch for your 2019 Nissan Titan XD short bed with the factory gooseneck is the Demco Hijacker Autoslide because unlike other sliding fifth wheel hitches, the Hijacker does not require you to leave your Nissan's cab just to…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 8

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 9

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 10

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 11

A wedge is needed, yes, and the Lippert Turning Point pin box does come with a universal wedge, but it is not a very good fit with the B&W Companion #BWRVK3710. So I highly recommend instead using the 5th Airborne Custom Wedge for B&W Fifth…

view full answer...

Answer 12

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Weight of Demco Nissan Rail Kit Adapter and Capacity

Product Page this Question was Asked From

Continue Researching