Factory Brake Controller Port Location on a 2003 Ford Explorer

Question

Question:

I thought the cable shipped with this unit is specifically made for factory installed towing kits. I got such on my 2003 Ford Explorer V8 Eddiebauer, but the cable doesnt fit any plug I have under the dash. I got one free plug, its trapeze shaped about 1.5 on top, 1.25 on bottom, and 0.5 high. Any advice? Should I take the unit to an installer? Thanks

asked by: Stefan B

0

Expert Reply:

The Tekonsha Wiring Harness, part # 3035-P is the correct harness for a 2003 Ford Explorer with a factory tow package with a 7-Way trailer connector. The # 3035-P harness will plug into the factory brake controller port located behind the glove box.

Open the glove box completely, you will need to push in the stops on the side of the glove box to do this. It is located on the left side of the opening, slightly above the opening. It is taped to another wire bundle. It will be a 6-pin connector that will mate with the connector on the end of the # 3035-P harness.

expert reply by: Jeff D

0

Answer 1

You can use sway control only with an adjustable ball mount in one of two ways. First, you could use sway control bracket #RP26003 which will fit a ball mount platform up to 2.610 inches wide. It also has a 1 inch diameter hitch ball hole. The…

view full answer...

Answer 2

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 3

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 4

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...