Using the Rhino Rack Nautic 581 Kit on Rhino Rack HD Bars

Question

Question:

Will the 581 rhino yak holders mount to rhinos HD square bars?

asked by: Jeff

0

Expert Reply:

The Rhino Rack Nautic Rear Loading Carrier, part # RR581 will fit your Rhino Rack HD square bars if you add the HD Fitting Kit, part # HD-FK2. These will replace some of the mounting parts included with the Nautic to fit your HD bars.

expert reply by: Jacob W

0

Answer 1

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 3

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 4

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 5

Yes, the best option we can offer you to add fuel capacity is with the DeeZee Truck Bed Auxiliary Tank part #DZ91752X which should fit in the space you have between the cab and 5th wheel hitch no problem as it is only 9" deep. I don't have…

view full answer...

Answer 6

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 7

The Trailer Hub and Drum Assembly part #AKHD-545-35-K is the correct replacement for an AL-KO 7230. In regards to the braking assemblies, I suggest getting a new pair, the Electric Trailer Brake Kit part #AKEBRK-35-SA. This option will save you some…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 10

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 11

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 12

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Using the Rhino Rack Nautic 581 Kit on Rhino Rack HD Bars

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching