What 5 On 5 1/2 Hub Available For Timbren Axle-Less Trailer Suspension System

Question

Question:

Is there a 5 on 5 1/2 hub available for the Timbren Axle-Less Trailer Suspension System? If so, what is your part number? Thank you.

asked by: David M

0

Expert Reply:

The Timbren options we have available fit a 5 on 4-1/2 bolt pattern or a 6 on 5-1/2 bolt pattern.

I recommend measuring your bolt pattern to make sure 5 on 5-1/2 is what you need. To confirm your measurement, use the distance between the center of one bolt hole to the center of the bolt hole adjacent to it (article on bolt patterns attached). If this measurement is 3-1/4 inches then you have a confirmed 5 on 5-1/2 pattern.

If the 5 on 5-1/2 pattern holds true then a Timbren option is not available at this time. However, we do have hub and drum options available. The Trailer Hub and Drum Assembly Item # AKHD-555-35-k for non-EZ Lube or The Trailer Hub and Drum Assembly Item # AKHD-555-35-EZ-K for EZ-lube style. Both fit a 5 on 5-1/2 bolt pattern and work with bearings Item # L44649 and bearings Item # L68149. Make sure to check your bearings to verify the correct fit needed.

If you are open to making a wheel change to a 5 on 4-1/2 or 6 on 5-1/2 bolt pattern then a Timbren system would be available. I am attaching a link to our wheels options for your consideration.

If you have or would change to a 5 on 4-1/2 bolt pattern then I recommend Timbren Axle-Less Trailer Suspension System Item # A35RS545E. It is designed for 3500 lbs, electric brakes, and has EZ-Lube spindles.

Please contact me if there is anything else I can do for you with regards to making a correct recommendation for your needs.

Additional articles and videos attached.

expert reply by: Brint H

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 3

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are…

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 9

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 10

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 11

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

What 5 On 5 1/2 Hub Available For Timbren Axle-Less Trailer Suspension System

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching