Will the TorkLift # TLD4101 and # TLD3109 Fit a 2005 Ram 3500 4x4 with Factory Step and Hitch

Question

Question:

Order no.######### Part no TLD4101 Part no TLD3109 ARE THESE PARTS CORRECT FOR 2005 Dodge 3500 4x4 single wheel factory steps Factory hitch 4 door

asked by: Al

1

Helpful Expert Reply:

The TorkLift Custom Frame-Mounted Camper Tie-Downs # TLD4101 for Front and # TLD3109 for Rear are compatible with your 2005 Dodge Ram 3500 4x4 with the step underneath the truck bed and your factory installed hitch.

Your order is correct.

I have attached an installation video of the rear tie-downs on a 2004 Dodge Ram for you to reference.

expert reply by: Jon G

1

Answer 1

The correct Timbren kit for a 2004 Dodge Ram 2500 with slide-in camper is the Timbren Rear Suspension Enhancement System part #T94VR. I confirmed this with Timbren for you. This is the model designed for service applications.

view full answer...

Answer 2

There seems to be a bit of confusion here, which I'll try to clear up. There are 3 main capacities related to the weight your vehicle can handle that you generally want to know; your payload (cargo) capacity and towing capacity are going to be…

view full answer...

Answer 3

It sounds like you're trying to install a TorkLift Front Tie Down #TLD4101 and regardless of whether or not an under-bed gooseneck hitch is present you will still be able to install front and rear tie downs on your 2005 Dodge Ram 2500. These tie…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...