Weights of Ladder Racks with Over-the-Cab Extension for 2001 Ford F-250 Long Bed Pickup

Question

Question:

How much does the 8foot over the cab rack weigh. Thank you

asked by: Joel B

1

Helpful Expert Reply:

The various ladder racks with over-the-cab extension that we offer for your 2001 Ford long-bed pickup are shown on the linked page.

These include cost-effective fixed type racks like the Erickson # EM07707 which weighs approximately 162-lbs.

On each item's page the shipping weight appears above the yellow Add to Cart button; just deduct about 5-lbs for the shipping carton to estimate the actual rack weight.

expert reply by: Adam R

1

Answer 1

Yes we can help you with a spare tire cover to fit your tire size 235/75R15 which has an overall diameter of about 29-inches and a width of about 9-1/2-inches. You can choose any spare tire cover from those shown on the linked page, all of which fit…

view full answer...

Answer 2

The Rola Haul-Your-Might T3 Truck Bed Ladder Rack #59799 is going to fit with your 2013 Toyota Tacoma as long as it has a Deck Rail System. The rack installs by sliding into the bed rails on your truck, and simply clamps into place. When you want to…

view full answer...

Answer 3

If you are using 2 of the 3500 pound axles, #T3584F-EZ-8974, then the combined capacity of the axles would be 7,000 pounds. Provided the gross trailer weight does not exceed the axle capacity you could absolutely use them on your car hauler. I have…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 6

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 9

When measuring for a trailer cover you want to measure from the front of the trailer box, not the tongue, to the rear including anything that is attached to the rear. This will include a spare or a ladder at the farthest edge at the rear of the…

view full answer...

Answer 10

To determine the location for the front and rear hangers on your tandem axle trailer you will first need to make sure that you have the correct center point for your equalizer hanger. The center point of your equalizer hanger needs to be located…

view full answer...

Answer 11

The correct bearing kit for your 2018 Winnebago Micro Minnie 2108DS with Lippert 3,500 Lb axles is the Bearing Kit for #84 Spindles part #BK2-100 which uses L44649 and L68149 bearings.

view full answer...

Answer 12

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...