What Is the Correct Bearing Kit for a 2018 Winnebago Micro Minnie 2108DS

Question

Question:

I have a 2018 Winnebago Micro Minnie 2108DS. It has 3500 lb axles. I noted these Lippert numbers on the axle 126003 and 170613. Which bearing kit is correct for this trailer

asked by: Kelly S

0

Expert Reply:

The correct bearing kit for your 2018 Winnebago Micro Minnie 2108DS with Lippert 3,500 Lb axles is the Bearing Kit for #84 Spindles part # BK2-100 which uses L44649 and L68149 bearings.

expert reply by: Conner L

0

Answer 1

Your 2017 Winnebago Micro Minnie 1700BH has a 3,500 lb axle, so for just the bearing kit you will need the Bearing Kit #BK2-100. For a replacement hub and drum the correct part is the Dexter Trailer Hub and Drum Assembly #84546UC3. Then for grease…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 5

The ALKO 4,400 lb axles use the same bearing sizes as the standard 3,500 lb alxes. If you want USA made bearings, I recommend the Bearing Kit #TMK52VR. This kit comes with the Timken brand bearings which are all made here in the USA.

view full answer...

Answer 6

Yes, the Timken Bearing Kit #TMK52VR will fit your 3,500 lb axle as it fits an standard #84 spindle. The only time this kit won't fit with a 3,500 lb axle is if the trailer/axle is made before the 2000's since that's about the time that…

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

Hello Jeffrey, While I'm sure we have a bearing kit for your car trailer, we don't have any way of knowing off-hand or cross-referencing what bearings you need. You mentioned you have them out, so you should be able to see the part number…

view full answer...

Answer 9

You are going to want either our Bearing Kit #BK2-100 or the Timken Kit #TMK52VR. Both of these kits will give you the inner/outer bearings and races along with a grease seal and cotter pin/D-washer for one hub. You always want to replace the race…

view full answer...

Answer 10

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

What Is the Correct Bearing Kit for a 2018 Winnebago Micro Minnie 2108DS

Product Page this Question was Asked From

Continue Researching