Options for Laundry Racks for Use on Rear of RV

Question

Question:

It looks this I will lose clearance at the back of the RV with the rack installed on the bumper. Is there another option?

asked by: Marty

0

Expert Reply:

The upright posts of the Stromberg Carlson RV Bumper Mounted Clothes Line # CL-100 do angle back about 15-degrees when installed on the included bumper brackets. This means that the tops of those poles will be about 18-inches to the rear of the RV's back surface. If this does not provide you with the walk-thru access you need you might prefer their ladder-mount Drying Rack # CL-27.

The Extend-A-Line rack # CL-27 features six adjustable 30-inch steel arms that are easily moved side to side as needed. This rack option also offers twice the weight capacity of the bumper-mount laundry rack - 60-lbs total for all six arms. The Extend-A-Line rack can also be wall-mounted.

expert reply by: Adam R

0

Answer 1

Yes, the SumoSprings #SS26MV is the same as the TSS-107-47 that you mentioned.

view full answer...

Answer 2

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

I went ahead and pulled this Replacement I-Beam Jack Bracket #LC349975 from our warehouse to measure. I have attached the dimensions below. Hope this Helps.

view full answer...

Answer 5

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 6

Yes, you'd just need to reach out to a qualified welder and have them weld on spring seats like part #TRSS300 to the top side of the Trailer Axle Beam with Easy Grease Spindles #e45GR. It's super common to do for people who have an underslung…

view full answer...

Answer 7

The Mounting Post for Stromberg Carlson Extend-A-Line RV Mounted Drying Racks - Square Bumper or A-Frame #CL-01 you were looking at is 44" long as shown in the included diagram. While not designed to be used with a backup camera, it will give…

view full answer...

Answer 8

If the 2 inch hitch on your vehicle is rated for at least 400 pounds tongue weight capacity, I would recommend using the Pro Series Steel Solo Cargo Carrier and Folding Ramp, #PS10401-10402. This carrier features a ramp for loading things like a…

view full answer...

Answer 9

Thanks for the information, Luke! The Extang Revolution Soft Tonneau Cover EX54430 is the correct part number for your 2011 Ram 2500 short bed, and although it's been discontinued, the replacement tarp is part #EX53430 on our site.

view full answer...

Answer 10

Yes, if you install the Stromberg Carlson trailer hitch #SC45MR by welding it you'd have a 3,500 lb towing capacity which be more than enough to tow a 3,000 lb trailer.

view full answer...

Answer 11

The Truma LevelCheck Propane Tank Sensor part #TR77VR uses ultrasound technology to check the propane level, the same technology used in doctors offices for newborns. Simply turn the device on and run it up and down the tank, the light will turn…

view full answer...

Answer 12

I wasn't sure exactly what dimension you were looking for on the mounting bracket of the Trailer Valet part #STC-V211 so I attached a picture that has nearly every dimension for you to check out.

view full answer...

Options for Laundry Racks for Use on Rear of RV

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching