How to Slide Rails of Curt Double Lock Between Frame and Bed of 2012 Ford F-350

Question

Question:

If Im having a problem inserting and sliding the under bed rails in my 2012 Ford F-350 Diesel for the C60720, am I able to just loosen the 8 in-bed bolts to give me the 1/2 inch room I need? Ive never loosened bed bolts, so I dont know if that sounds too simple

asked by: Tim P

0

Expert Reply:

If you are having trouble sliding the Curt Double Lock # C60720 rails between the frame and bed of your 2012 Ford F-350, I would not recommend loosening the in-bed bolts; instead, the directions do recommend you cut a notch in the flange on the driver's side of the truck as show in the attached image. This should allow you the needed space to insert the rails.

expert reply by: Kyle S

0

click to enlarge

Answer 1

Since flat beds have a tendency to be a bit longer than standard truck bed I'd recommend putting the B and W Turnoverball #BWGNRK1500 right over the rear axle. Any further forward and you'd be more likely to have clearance issues between the…

view full answer...

Answer 2

There is not a custom fit gooseneck hitch and underbed rails for your 2000 Ford F-350 Cab and Chassis. Your best option is to use the B&W Turnoverball Underbed Gooseneck Trailer Hitch for Flatbed Trucks - 30,000 lbs #BWGNRK1500 which will require…

view full answer...

Answer 3

You do have the installation of the U-bolt safety chains correct for the Buyers Products 2-5/16" Fabricators Flatbed Gooseneck Hitch #3375613500. I have cut out and added below the section of the instructions for the #3375613500 which details…

view full answer...

Answer 4

I reached out to my contact at B&W and have a solution for you. Although none of the manufacturers we carry have a fit for the 34 inch frame, B&W has a work-around. If you have a flatbed, you can use the #BWGNRK1500 that gets welded to the…

view full answer...

Answer 5

To install the B and W Hitch part #BWGNRK1500 you will need to provide 1/4 thick brace straps to attach the hitch to the frame of the trailer. If you check out the install instructions I attached you can see more about the install process. The…

view full answer...

Answer 6

The dimensions are below for the B&W Turnoverball Underbed Gooseneck Trailer Hitch #BWGNRK1500. Overall dimensions of the plate- 6” X 8” Bottom of the plate to the bottom of the socket Fin (brace) – 2-1/4" Bottom of the plate to the end of…

view full answer...

Answer 7

Good morning. Both the #C60720 and the #C60720-5W are the same exact item. We give them different part numbers so that the item can be searched as both a gooseneck hitch and as a mount for the Demco Recon 5th wheel hitch, Both kits include the rails,…

view full answer...

Answer 8

There is an underbed gooseneck hitch that is going to work with your 2008 Ford F-250 Super Duty, but the Curt Double Lock #C60720 will not be a fit. Instead, I recommend the B&W Turnoverball Underbed Gooseneck Trailer Hitch #BWGNRK1500 which is…

view full answer...

Answer 9

The Curt EZr Double Lock #C60683 and the Double Lock #C60720 are essentially the same gooseneck system with some minor differences. Mainly, the EZR sits lower by 3/8" in the truck bed, but it's main draw is that it's designed to be a bit…

view full answer...

Answer 10

Yes, the Firestone air bag kit #F2703 you have for your 2016 Ford F-250 is compatible with in-bed hitches like the Curt gooseneck part #C60683 that you referenced as well.

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...