Bolt Hole Dimensions of the Curt Trailer Hitch Receiver # C13193

Question

Question:

Can you give me the overall width of the C13193 where it mounts onto the vehicle. Also I need to know the from where it mounts to the top of the receiver.

asked by: John P

0

Expert Reply:

From the center of one bolt hole to the center of the mirrored one on the other bracket of the Curt Trailer Hitch Receiver # C13193 is 35-1/2" as I have demonstrated in the attached photo.

The top of the collar around the hitch receiver opening sits about 1 inch below the mounting brackets and the top of the hitch receiver opening sits about 1-1/4 inches below the mounting brackets.

This trailer hitch is a custom fit for your 2017 Ford Transit T350 and is designed to bolt up to pre-existing holes in your frame.

If you let me know what you will be using this trailer hitch for I can make some recommendations for you.

expert reply by: Jon G

0

click to enlarge

Answer 1

I went out to the warehouse to take some measurements of Curt trailer hitch #C14082. I made a picture showing the measurements for you. The bolt holes, starting from the one furthest forward on the vehicle, measures 2-3/4 inches to the center of…

view full answer...

Answer 2

The Curt Trailer Hitch Receiver part #13028 is designed to fit the following vechiles: - 88-91 CHEVY/GMC 4 DR CREW CAB ONLY - 73-79 FORD 250 CREW CAB - 73-06 CHEVY/GMC FULL SIZE CAB & CHASSIS w 34" FRAME - 73-06 FORD PICKUP: CAB AND CHASSIS…

view full answer...

Answer 3

From side to side, the mounting holes measure 31-1/4 inches apart, center to center. All three sets of holes are the same distance apart. From rear to front, beginning at the rear of the vehicle the distance from the first set of holes to the second…

view full answer...

Answer 4

34 inch frame widths are pretty common cab and chassis trucks. The B and W Hitch part #BWHDRH25122 that you referenced is designed to fit cab and chassis trucks with a 34 inch width measured from outside to outside on trailer frames. If you measured…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Bolt Hole Dimensions of the Curt Trailer Hitch Receiver # C13193

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching