Will a Capture Plate for a PullRite SuperGlide Fit the Flex Air Pin Boxes

Question

Question:

will the flex air king pin box accept the adopter plate for the pull rite supper slide hitch

asked by: Craig M

0

Expert Reply:

We do not sell the capture plate you need but it is 331761. That is the model indicated by PullRite that fits the Flex Air pin boxes such as # LC328492.

expert reply by: Michael H

0

Answer 1

In order to choose the correct Trailair Flex Air pin box like the #LC328492, or any other pin box for that matter, is by checking the spec sticker on the current pin box for a model number. We don't have a database that tells us what pin box is…

view full answer...

Answer 2

The reason the Demco Capture Plates #DM6171 aren't working with your Lippert Turning Point pin box is because they were specifically designed for Trailair Rota-Flex pin boxes. Since you have a Demco Autoslide #DM8550037 you'll need to lockout…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 9

We have the following Gen-Y shock absorbing 5th wheel pin boxes which are compatible with the Lippert Rhino pin box bolt pattern. The weights listed below are the maximum capacities the pin box is capable of supporting. 21,000 lbs - 3.5K TW #GY86GR…

view full answer...

Answer 10

Hey Robert! Yes, the Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shock Absorbers #RM-2460-2570 can be used to replace the MORryde LRE suspension kit you currently have on your 2006 Keystone Montana. Just verify your axles have a 3"…

view full answer...

Answer 11

There should be a sticker or plate on the pin box itself that lists the manufacturer and model of the pin box. If it is not present then there are some measurements you can take to determine the model of the pin box. I have included a link that…

view full answer...

Answer 12

Most standard pin boxes will not make a 90 degree turn in anything less than an 8 foot truck bed, but that is due to being too close to the cab - not the rails. You mentioned you wanted to replace the Rota-Flex with the Gen-Y hitch. Your old pin box…

view full answer...

Will a Capture Plate for a PullRite SuperGlide Fit the Flex Air Pin Boxes

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching