Available 23-1/2 Inch Replacement Double Eye Spring

Question

Question:

I need a 23.5 x 2in. Double eye trailer spring for my rv.

asked by: HENRY V

0

Expert Reply:

We carry one 23-1/2" double eye spring, # SP-113275. This spring is for a 2,000 lb axle, has three leaves, a spring width of 1-3/4", an eye diameter with bushing of 9/16" and an eye diameter without the bushing of 11/16". I've added a link to a video review of this spring for you to take a look at.

expert reply by: Kyle S

0

Answer 1

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 2

Technically, a trailer rated for 10,000 lbs can have 5 lug hubs. They are most common on 3,500 lb axles but can be used on the rare 4,000 lb axles as well. You could have a gooseneck or 5th wheel trailer with the 10,000 lb capacity and tandem axle 5…

view full answer...

Answer 3

Thank you for the pictures! It looks like you've got some sort of square drop axle on your trailer and if you can't find an identifying sticker, I can still help you figure out what you've got so that you can make the swap to electric…

view full answer...

Answer 4

We do carry a range of trailer suspension parts including leaf springs, both double-eye and slipper types like your 2-inch-wide slipper spring. However, the shortest such slipper springs are 26-5/8-inches long. These are intended for applications on…

view full answer...

Answer 5

I do have some info for you but there isn't a torque spec for shackle bolts like the Shackle Bolt for 1-3/4" Wide Double Eye Springs part #007-003-01. Instead, you'll want to tighten the nut for the bolt until snug and then back it off a…

view full answer...

Answer 6

The Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased #AKHD-545-35-K you were looking at are pre-greased with a Lithium complex, multipurpose grease. When repacking the bearings in the future you will want…

view full answer...

Answer 7

The trick for hanger spacing is to subtract around 3/8 of an inch from the spring length (eye to eye) and then use that dimension for the hanger spacing on a single axle trailer. So for a 23-1/8 inch long leaf spring a spacing of 22-3/4 inches would…

view full answer...

Answer 8

With your Triangular Equalizer #TREQ310 you will have a 4 inch height and 6-1/16 inch on center width for your suspension system. I did a little research and the Una-113 springs are 23.5 inches and 3 leaves with a 1000 lb capacity. This is the same…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Available 23-1/2 Inch Replacement Double Eye Spring

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching