How Does Washer Face when Installing Curt Hitch # C13146

Question

Question:

The washer has a curve to it. Should I put the convex or concaved part of the washer against the nut head?

asked by: David

0

Expert Reply:

You'd want to put the convex side of the washer against the bolt head of the hardware that comes with the Curt hitch # C13146 when installing it. That way the head pushes it flat as you tighten it which acts as a lock nut.

expert reply by: Jameson C

0

Answer 1

We have the Curt Trailer Hitch Receiver #C26VV for your 2024 Toyota Grand Highlander Hybrid Platinum MAX. This hitch requires no drilling and will install with the included hardware into existing holes in your frame. I do recommend installing the…

view full answer...

Answer 2

We already carry the Curt Trailer Hitch Receiver(13519) #C26VV. This is the receiver for the new 2024 Toyota Grand Highlander. If you will be towing or need Auxiliary Lights #C53201 we do have the Curt T-Connector Vehicle Wiring Harness #C79VV…

view full answer...

Answer 3

Yes, it does. The Curt Trailer Hitch item #C26VV has been confirmed to fit the new 2024 Toyota Grand Highlander. This hitch is custom fit and bolts to the Highlander with included hardware. This is a class III hitch with a 2" receiver. It…

view full answer...

Answer 4

I have attached a picture below of the Curt Hitch item #C26VV installed on a 2024 Toyota Grand Highlander. I really like this hitch because the crosstube installs behind the rear bumper leaving only the 2" receiver exposed. The Curt Hitch…

view full answer...

Answer 5

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 6

Yes, the Curt Trailer Hitch Receiver #C26VV will fit your 2024 Toyota Grand Highlander hybrid. I have included an image below that was sent to us of the receiver installed on a hybrid. I always recommend installing at least a 4-Way #C59236 when you…

view full answer...

Answer 7

There isn't a lot to the installation of the #C79VV so it is likely one of two things. The first is the ground connection. Double check the ground connection and make sure it is secure on a clean, bare-metal surface. The other possibility is that…

view full answer...

Answer 8

Yes! We have both a hitch and wiring for your 2024 Toyota Grand Highlander. Hitch - Curt Trailer Hitch Receiver #C26VV Wiring - #C59236 If you are planning to do any towing, you can add the etrailer Ball Mount Kit #989900 to round out a tow package.

view full answer...

Answer 9

The Curt Trailer Hitch Receiver #C26VV fits your 2024 Toyota Grand Highlander. This gives you a 2" receiver opening allowing for a large selection of hitch mounted accessories and ball mounts. I recommend installing the Curt Curt Powered Tail…

view full answer...

Answer 10

For your 2018 Acura MDX the aftermarket trailer hitch that will be most similar to the OEM/factory unit is the etrailer.com Class III Hitch #e98840. The primary difference between the OEM hitch for the Acura MDX and an aftermarket model is their…

view full answer...

Answer 11

Dirty or corroded weld nuts on vehicle frames that prevent hitch bolts from threading are actually pretty common. Especially on vehicles that have seen a few winters. There are a couple ways you can clean out the threads so that the bolts will…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

How Does Washer Face when Installing Curt Hitch # C13146

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching