Troubleshooting Hitch Lock with Key Broken Off Inside

Question

Question:

In an attempt to remove the lock and attach a bed extender, the key broke off. How do I remove the device?

asked by: Terry

0

Expert Reply:

For your Master Lock Hitch Receiver and Coupler Latch Lock Set - Padlock - 1-1/4" and 2" Hitches # 2848DAT with a broken key in the cylinder, your only option is to contact a locksmith to see if there is a way to remove the broken key without damaging the cylinder or drill out the cylinder to remove it.

expert reply by: Jason S

0

Answer 1

You can purchase Re-Keying Kit, #DTLBM02RK, to re-key your ball mount. The kit includes a tool to remove the locking cylinder you have in the ball mount now. Once you receive the kit, you will need to put some air tool oil in the hole that the lock…

view full answer...

Answer 2

In order to replace the trailer hitch on a motorhome you will need to go with a universal hitch as they do not offer bolt-on options for this. I recommend the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver part #41990-07 or part #41990-16…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 6

Here are the steps to prepare your 2023 Ford Bronco Big Bend for flat towing. The transfer case and transmission will be in neutral with the ignition off. This information is in your owners manual. Switching Neutral Tow On 1.Switch your vehicle to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The Roadmaster D-Ring adapters like the part #RM-035-1 can be used with the Demco tow bars.

view full answer...

Answer 9

The best SumoSprings for your 2023 Ford Bronco depends on what you are using them for - just to improve your ride a bit on rougher roads, or to help with sag when you are towing or maybe using an accessory. I'll go ahead and list out the options…

view full answer...

Answer 10

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 11

To install a 7-Way harness on your 2023 Ford Bronco without the towing package, you will need two separate wiring harnesses because they don't make just one that'll do the job. The first harness you'll need is the Curt T-Connector Vehicle…

view full answer...

Answer 12

In regards to the Adapter 4 Pole to 6 Pole and 4 Pole Trailer Wiring Adapter part #37175, the blue or red wire could be used for reverse lights. That said, you would just need to be sure you hook the reverse lights up on the trailer side connector to…

view full answer...

Troubleshooting Hitch Lock with Key Broken Off Inside

Product Page this Question was Asked From

Continue Researching