What Size Wheel and Tire Would Fit on Trailer Hub part # AKHD-865-7-2-K

Question

Question:

Will a 15in wheel fit on these hubs?

asked by: Geoffrey C

0

Expert Reply:

The hub you referenced part # AKHD-865-7-2-K requires at least a 16 inch diameter wheel and tire like the part # LHACK133 which has the correct bolt pattern and comes with a ST235/80R16 tire mounted to it.

expert reply by: Jameson C

0

Answer 1

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 4

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

I'm sure we can get you a hub and drum assembly for your trailer but there's quite a bit of info needed in order to do so. To find the correct hubs you will need to take apart your current hub assembly and look at the bearings themselves;…

view full answer...

Answer 8

According to my research, your 92865A-1 hub/drum has a 25580 inner and an 14125A outer bearing and a 8 on 6-1/2 inch lug pattern, as does the AxleTek #AKHD-865-7-2-K hub drum you referenced. The #AKHD-865-7-2-K would be an acceptable replacement for…

view full answer...

Answer 9

I have a few options for you to help with identifying the correct replacement hubs on your trailer. The first and easiest method would be to crawl under the trailer and look for the axle tag on the beam. This should give an axle capacity which we can…

view full answer...

Answer 10

For your 1st question, yes the Dexter Nev-R-Adjust Electric Trailer Brakes #23-464-465 are going to fit the 5 bolt mounting flange on your 7,000lb axle for your 2020 Grand Design Solitude 380FL. For your 2nd question, yes the Trailer Hub and Drum…

view full answer...

Answer 11

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 12

That's pretty crazy that you ended up shearing off all 8 of your wheel studs. Normally they will break one at a time but not all together like that. This makes me wonder if maybe you were losing them all one at a time until the last few went out…

view full answer...

What Size Wheel and Tire Would Fit on Trailer Hub part # AKHD-865-7-2-K

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching