Is an Andersen Hitch Pin Lock Available That can be Keyed Alike to Locks Already Owned?

Question

Question:

I have a rapid hitch adjustable height ball. I also have the two pin Anderson hitch locks. Is it possible to purchase one more hitch pin lock smaller pin keyed the same as the two that I have? Thanks

asked by: Jan S

0

Expert Reply:

You would need to get another Rapid Hitch Trailer Lock # AM3492 as you would not be able to get another lock keyed alike to the locks you already have.

I've added links to review videos of this product for you to take a look at.

expert reply by: Kyle S

0

Answer 1

I do have an option for you but there are no replacement keys available for the Curt Lock Set for Adjustable Channel-Style Mounts part #C23556. If the keys can no longer be found then you can either call a locksmith to unlock them or just use a…

view full answer...

Answer 2

I spoke with my contact over at Curt about lock set #C23556. He said that while the exact number is not known there are potentially thousands of possibilities. One thing is certain though and that is that they are not all the same!

view full answer...

Answer 3

The interior channel width of the Curt adjustable ball mount part #C45900 that you referenced is 3 inches.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...