Recommendation for Trailer Ramp Hinge that Can Handle a 500 Pound Motorcycle
Question:
Good morning. I have a small utility trailer with a motorcycle tire chock installed and am looking to replace the rear carriage bolt setup that is used to attach the folding loading ramp with a stronger hinge setup. I am not sure what type of hinges to get welded on. It needs to be able to support the weight of loading a 500lb motorcycle. Thanks!
asked by: Joe
Expert Reply:
For your ramp and 500 pound motorcycle I recommend using a couple of ramp hinges, # PLR1902, sold in quantities of 1. This is a heavy duty ramp hinge and has a grease fitting so you can easily keep It lubricated.
I am not sure how wide your ramp is or the available space you have to mount a hinge but the overall length of this hinge is 8-3/16. For something a little shorter we have dump door hinge # PLR1904-Z which is under 5 inches wide. I have linked videos on both of these hinges for you.
Products Referenced in This Question
Ramp Door Hinge - 8-3/16" Long - 1" Pin Diameter - Steel
- Trailer Door Hinges
- Ramp Door Hinge
- Greasable Pin
- Steel
- 8-3/16 Inch Long
- 4 Inch Wide
- Weld-On
- Polar Hardware
more information >
Dump Door Hinge for Dump Trailers - Steel - Qty 1
- Trailer Door Hinges
- Dump Door Hinge
- Greasable Pin
- Steel
- Weld-On
- Polar Hardware
more information >
Product Page this Question was Asked From
Butt Hinge w/ Removable Pin - 5" Long x 4-7/8" Wide - 1/2" Pin Diameter - Aluminum
- Trailer Door Hinges
- Butt Hinge
- Removable Pin
- Aluminum
- 5 Inch Long
- 3/16 Inch Diameter
- 4-7/8 Inch Wide
- Bolt-On - No Pre-Drilled Holes
- Weld-On
- Polar Hardware
more information >
Continue Researching
- Shop: Ramp Door Hinge - 8-3/16" Long - 1" Pin Diameter - Steel
- Shop: Dump Door Hinge for Dump Trailers - Steel - Qty 1
- Video: Polar Hardware Enclosed Trailer Parts - Doors - PLR1904-Z Review
- Shop: Over the Seal T-Strap Hinge w/ Narrow Bracket - 180 Degree - 12"Long - Polished Stainless Steel
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Shop: Trailer Hitch
- Q&A: Can Barn Doors of Trailer Ramp be Changed to Ramp Door
- Q&A: Dimensions of Polar Steel Dump Door Hinge PLR1904-Z
- Q&A: Aluminum Hinge for a Utility Trailer Tailgate
- Q&A: Replacement Hinge Recommendation for MAXXD Dump Trailer
- Q&A: Recommended Hinges And Ramp Assist For Steel Ramp
- Q&A: Can Bolt of Dump Door Hinge # PLR1904-Z Be Removed
- Video: Polar Hardware Enclosed Trailer Parts - Doors - PLR2512-SSP Review
- Article: How to Choose the Right Trailer Hitch Class
- Video: etrailer Enclosed Trailer Transition Plate Review
- Q&A: Installation of Ramp Door Hinge Polar 1902
- Search Results: fender
- Shop: Trailer Wiring
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End
- Search Results: 25580
- Shop: Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Polar Hardware Enclosed Trailer Parts - Doors - PLR1902 Review
- Search Results: 90160
- Shop: Gooseneck Hitch
- Video: Review of etrailer Enclosed Trailer Transition Plate - e32JR
- Article: Trailer Wiring Diagrams
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Shop: Fifth Wheel Hitch