Diameter Hole Required for Installing Peterson Grommet # 166-18K

Question

Question:

What size hole for the peterson grommet?

asked by: John

0

Expert Reply:

The hole size the part # 166-18K is designed for is 2-5/16 inch.

expert reply by: Jameson C

0

Answer 1

Yes, the 2-1/4" hole saw would be perfect for the Sealed 2" Round Trailer Clearance and Side Marker Light part #MC53RB with the 2" Round Grommet part #A54GB. This setup calls for a 2-5/16" hole but you are going to have more…

view full answer...

Answer 2

I have a couple options for you as we do not have a box like the Buyers Products Tail Light Mounting Box #337LB383SL with a opening on the side for the Peterson LED Clearance and Side Marker Trailer Light #PE57PR. First would be to drill a 3"…

view full answer...

Answer 3

From what I could find out, the GenMini1 is designed to only be used with 12 volt lead-acid batteries. If you are using two 6 volt batteries, this cannot be used. The flashing LED lights are referring to the voltage being incorrect. To charge your 6…

view full answer...

Answer 4

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 5

We have a really great kit that comes with everything you'd need to convert your 2021 Vanleigh Pinecrest 335RLP from tandem 6k drum brakes to electric over hydraulic disc brakes with the HydraStar Disc Brake Kit w/ Actuator for Triple Axle…

view full answer...

Answer 6

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 7

My research indicates that grease seal part 125255UC has an outer diameter of 1.980-inches and this correlates with the hubs that use bearing #L44649. The seal part most often used with inner/outer bearing L44649 is seal part #10-9 which has an inner…

view full answer...

Answer 8

A TruRyde rvd-h-865 7k hub/drum like # AKHD-865-7-2-K uses 1/2-inch drive-in studs that are 1-5/16-inches long. For a replacement stud you can use #165981. This is slightly longer at 1-1/2-inches but it has the same 1/2-inch diameter. They are also…

view full answer...

Answer 9

I recommend the Solera RV Slide-Out Awning - 13'1" Wide - 48" Projection #LCV000168109 which will fit RV's with slide outs that are 152" to 157" wide and up to 48" long, the awning rail is included. This is also…

view full answer...

Answer 10

We highly recommend against double towing and many states either don't allow double towing or have numerous restrictions. There are some states that limit the total length of all 3 units, some only allow certain types of trailers behind the 5th…

view full answer...

Answer 11

For a 24 inch hitch extender the best option is the Curt part #C45048 cut down to the 24 inch length. This has a capacity of 8,000 lb trailer weight when used with a WD system like you mentioned. Since this is the only extender option that's…

view full answer...

Diameter Hole Required for Installing Peterson Grommet # 166-18K

Product Page this Question was Asked From

Continue Researching