Installation Instructions for Curt Trailer Hitch Receiver # C13329

Question

Question:

Curt Trailer Hitch Receiver - Custom Fit - Class III - 2 Item # C13329 Please could you send me a copy of the installation instructions to help me decide if I can handle installation. Thank you so much.

asked by: Spencer L

0

Expert Reply:

I have attached the complete installation instructions for the Curt Trailer Hitch Receiver # C13329 that you can look through.

This trailer hitch is designed for the 2017-2018 Kia Niro and no drilling will be required, as it will use existing mounting holes in the vehicle's frame. The exhaust will need to be temporarily lowered and some minor trimming on the plastic panel will be required during installation.

expert reply by: Chris R

0

Answer 1

If the cause of the premature failure is attributed to towing outside of the manufacturers recommend paraments then they can void the powertrain warranty. For example, if the towing capacity is listed at 2,000 lbs and they can prove you were towing a…

view full answer...

Answer 2

Finding someone to install a hitch like the Curt hitch part #C13329 is pretty simple. What you'll want to do is find a local mechanic to you with a good reputation and take the hitch to them. Hitch installs are pretty basic for mechanics compared…

view full answer...

Answer 3

The best trailer hitch for your 2018 Kia Niro is the Curt Trailer Hitch Receiver #C13329 because of its hidden crosstube and because it is a Class III hitch with a 2" receiver, which gives you many more options for accessories such as bike racks…

view full answer...

Answer 4

Not all models of the 2019 Kia Niro have an auxiliary battery at the rear of them which is why a power wire wasn't ran to it when installing the part #118749. If you have a PHEV which has the second battery you could do this.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Installation Instructions for Curt Trailer Hitch Receiver # C13329

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching