What is the Outer Diameter of the Slotted End of Crank Handle RVLG-HDL

Question

Question:

What is the outside diameter of the slotted end of the crank?

asked by: Anthony K

0

Expert Reply:

According to my calculations the outer diameter of crank handle # RVLG-HDL is a hair more than 3/4 inches. Its actually closer to 13/16 inches.

expert reply by: Michael H

0

Jim S.

4/21/2020

Thanks but I think it is to small. I have a handle for my old camper but looking for a spare. The one I have is 7/8 outside diameter and inside diameter is 11/16. Do you have a spare for me? Jim

Reply

Chris R.

4/22/2020

We have a pretty large selection of replacement crank handles. Do you happen to know what model jack/landing gear system you have?

Helpful Links

dept-pg-accessories_and_parts-pt-handles_and_cranks.aspx

Reply

Answer 1

The end of the Replacement Manual Crank Handle #LC119226 is a slotted cylinder which means there isn't a socket that would work as a substitute.

view full answer...

Answer 2

The Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear #RVLG-HDL is designed to be a replacement handle for Landing Gear Set #RVLG-8HDL. Replacement handles attach to landing gear in a number of ways so they need to be matched…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

What is the Outer Diameter of the Slotted End of Crank Handle RVLG-HDL

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching