Replacement Landing Gear Motor Recommendation for 2007 Keystone Montana

Question

Question:

I have a 1-065-041012-01 motor and a gear box model # 1a065012-02-01 hard to read. Is there a motor assembly that is a little heavier duty 2007 keystone Montana

asked by: Kimn B

0

Expert Reply:

Based on the model number you listed the correct replacement motor you would need is the # LG-142178. It is an exact replacement for your Venture motor so it would bolt right up.

I wish we had something heavier duty but at this time we do not have anything.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The price difference does seem backwards, but the faster speed part #LG-141893 has the same weight capacity as the lower speed part #LG-142178 that you also referenced. It's a difference of 5,500 RPM and 7,140 RPM so you would definitely see a…

view full answer...

Answer 2

It could be the motor but it could also be the screw/nut inside the jack leg that is causing the problem. Since you mentioned that it is hard to crank it manually I suspect that it is likely the screw and/or nut. On jacks that have an ACME screw the…

view full answer...

Answer 3

Other than the clicking sound is the landing gear functioning properly? Usually, when someone says they have clicking the jacks are either working slowly or not at all. Check the connection of the ground wire on the motor and make sure it's…

view full answer...

Answer 4

If it a jack isn't able to raise a trailer properly it's generally because it isn't getting enough power or there is hardware problem. I would first check the wiring and make sure there isn't a short. Also, inspect and clean the…

view full answer...

Answer 5

Most likely yes, but you'd need to measure the current mounting brackets of your landing gear to know if the #RVLG-8000 is going to fit and work well. Compare the measurements to the picture I attached and if your mounting brackets match this kit…

view full answer...

Answer 6

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 7

The Replacement Motor for Stromberg Carlson Electric Landing Gear - 5,500 lbs #LG-142178 is the correct replacement motor for the discontinued Atwood 75721. The #LC141893 you asked about will also work and is a higher speed motor so it will give you…

view full answer...

Answer 8

The Replacement Motor for Stromberg Carlson Electric Landing Gear - 5,500 lbs item #LG-142178 you were looking at is the correct replacement motor for the discontinued Atwood 75721. The Gearbox for Venture Electric 5th Wheel RV Landing Gear…

view full answer...

Answer 9

It sounds like the gearbox could be bad or possibly the motor, this could be easily confirmed by removing each of the components (gearbox/motor) and testing them separately. The gear boxes are luckily pretty standardized and not terribly expensive,…

view full answer...

Answer 10

The replacement motor for your landing gear is #LG-142178 This will work well for you.

view full answer...

Answer 11

From what I could find it looks like your ADTH 1RV-200 motor has a weight capacity of 6,500 lbs. You can use a motor that is rated for a higher capacity, like our replacement motor #LC142178 for Ram landing gear which is rated at 8,000 lbs. Just keep…

view full answer...

Answer 12

For the gearbox on your 2008 Forrest River Sandpiper I recommend the Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear Assemblies #LC276602. The aluminum casing is far more sturdy than the plastic housing options. If you…

view full answer...

Replacement Landing Gear Motor Recommendation for 2007 Keystone Montana

Product Page this Question was Asked From

Continue Researching