Tang Washer for 1-1/6 Inch Spindle

Question

Question:

I'm looking for tang washers for 1-1/16 inch spindles. Do you have them?

asked by: Amit K

0

Expert Reply:

We do not have tang washers for 1-1/6" spindles, however, it is possible you might need a washer for a 1" diameter spindle, because 1-1/6" is the same diameter as bearing # L44649, which goes to 1" spindles. I recommend double checking with a digital caliper just to make sure you don't need a 1" washer such as Replacement Spindle Washer - Tang Type # 5-101.

I've added a link to our page with each of our spindle washers for you as well.

expert reply by: Kyle S

0

Answer 1

The #BK2-100 Bearing Kit for #84 Spindle L44649/L68149 Bearings 10-19 Double Lip Seal will work. You have EZ Lube spindles which do not use a cotter pin. The spindle has a tube in it for the grease to be pumped in. Instead it uses a tang washer,…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

The biggest difference between the servo styles that you'll notice is between free backing plates and the others. The free-backing plates will allow your trailer to back up without having the brakes lock up. With surge brakes typically when you…

view full answer...

Answer 7

Hey Tim, thanks for the picture of your current brake assemblies. While what you have doesn't look exactly like a free-backing setup you definitely can replace what you have with them. For that I would go with the etrailer part #AKFBBRK-35 which…

view full answer...

Answer 8

The ALKO 4,400 lb axles use the same bearing sizes as the standard 3,500 lb alxes. If you want USA made bearings, I recommend the Bearing Kit #TMK52VR. This kit comes with the Timken brand bearings which are all made here in the USA.

view full answer...

Answer 9

A replacement tang-style spindle washer like part #5-101 is intended to be installed behind the castle nut and have its prongs bent down so that they prevent the castle nut from rotating on an E-Z Lube type spindle. The castle nut holds the washer in…

view full answer...

Answer 10

Based on the seal measurement, it sounds as if the best fit is going to be the Bearing Kit, 15123/25580 Bearings,10-10 Seal, #BK3-110. The seal that is included in this bearing kit measures 2.125 (2-1/8) inches. The inner and outer bearing numbers…

view full answer...

Answer 11

The bearing kit part #BK3-110 that you referenced is the correct kit your Dexter 5,200 lb axles. This comes with all of the bearings, races, and seals you mentioned. I also attached a link to a rebuild video for this for you to check out as well.

view full answer...

Answer 12

The Never Fail Bushings like part #TRBU11566 and the Bronze Bushings like part #D014-077-00 are designed for 1-3/4" wide double eye leaf springs. There is not a version of these which are an upgrade over the factory nylon bushings for 2"…

view full answer...

Tang Washer for 1-1/6 Inch Spindle

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching