Will the Dexter Nev-R-Adjust Electric Trailer Brake Kit # 23-458-459 Replace 23-326 and 23-327

Question

Question:

I have part number 23-326 LH and 23-327 RH 6000 lb 12 x 2 brakes. Would this self adjust brake work as a replacement?

asked by: Jason S

0

Expert Reply:

Yes, the brake assembly kit part # 23-458-459 will be just what you need since it is a pair of 12 inch by 2 inch assemblies with a 6k axle capacity.

expert reply by: Jameson C

0

Answer 1

Hey Jesse, thanks for reaching out! The brakes you have are found in this kit: Dexter Nev-R-Adjust Electric Trailer Brakes #23-458-459, while the replacement hub and drum assembly can be found with this number #8-201-5UC3-EZ (comes with…

view full answer...

Answer 2

Yes we do have replacement shoes for the Dexter 6k Nev-R-Adjust assemblies part #23-458-459 with the part #K71-676 for the right hand side and the part #K71-675 for the left hand side.

view full answer...

Answer 3

The MTI number on your 8-201 hubs is simply a casting number. It does not indicate any information about the hubs or have anything to do with the actual part number. I'm not surprised to hear you have different outer bearings between the…

view full answer...

Answer 4

The Dexter Electric Trailer Brake Kit #23-105-106 are a replacement set for the 023-358-00. This kit includes a right and left brake assembly that is manually adjustable. I recommend the Dexter Nev-R-Adjust Electric Trailer Brake Kit #23-458-459 as…

view full answer...

Answer 5

Yes it sure will. The Dexter #23-458-459 consists of both the right and the left 6K 12 inch self-adjusting brake assemblies. Part #23-458-00 (or #23-458 which is the number we use) would only include the left hand brake assembly. If you click the…

view full answer...

Answer 6

The correct braking assemblies you'll need for a Dexter 6K Axle on Adam LQ Horse Trailer is the Dexter Nev-R-Adjust Electric Trailer Brake Kit part #23-458-459 and the correct hub/drum is the Dexter Trailer Hub and Drum Assembly part…

view full answer...

Answer 7

Electric trailer brakes like the Dexter Nev-R-Adjust Electric Trailer Brake Kit #23-458-459 should only utilize two wires, the power and the ground. You do need to connect each of the wires to your brake assemblies, and each should have its own…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

You can convert surge brakes to an electric over hydraulic braking system. To do this, you will need an electric over hydraulic actuator and a brake controller. For an electric over hydraulic actuator, I recommend looking at the Carlisle HydraStar…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Will the Dexter Nev-R-Adjust Electric Trailer Brake Kit # 23-458-459 Replace 23-326 and 23-327

Product Page this Question was Asked From

Continue Researching